Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Cisco Jabber for Windows can place Point to Point Video Call but can't place Multiparty Video Call

Hi,

                  

I have CUCM 8.6.2.21900-5 and Presence 8.6.4 and I have install Cisco Jabber for Windows ( CiscoJabber-Install-ffr.9-0-1.zip ) in 4 PCs .

We can place Point to Point Video Call but can't place Multiparty Video Call,

When we add 3rd party in Point to Point Video Call that time conference call automatically converts into Audio Call only.

Regards,

Shashank

12 REPLIES
New Member

Cisco Jabber for Windows can place Point to Point Video Call but

Do you have a video MCU or an ISR G2 with PVDMv3 DSPs with video conferencing resources defined in your MRG and MRGL that are assigned to the device pool that your Jabber devices are assigned to?

New Member

Cisco Jabber for Windows can place Point to Point Video Call but

We dont have any external video MCU or an ISR G2 with PVDMv3.

Is it required for multiparty video call ?

Can we configure CUCM to do multiparty video without MCU or ISR ?

New Member

Re: Cisco Jabber for Windows can place Point to Point Video Call

Without an ISR or an MCU or some sort of a bridging service, the answer is no.

Sent from Cisco Technical Support iPhone App

New Member

Cisco Jabber for Windows can place Point to Point Video Call but

Hi Michael,

I do have an ISR G2 router with pvdm3 configured as homogeneous.

I verified that the DSPs are being used when

I try to do the video conferencing, however

I cannot videoconference 3 devices.

Please note the the videoconference works

With my 9971 phones.

I'm using codec h264 cif-30-740.

Do you suspect a codec issue for jabber?

Re: Cisco Jabber for Windows can place Point to Point Video Call

What is the current official position on this?

I am interested in positioning Jabber for Windows Clients forming Video teleconferences using only PVDM3s on ISR-G2's.

From what I have read, it looks like this is supported.

I also find some inconsistent documentation about  'lecture mode', where one doc says its supported, but the other says its  not.  Are we limited to only active speaker via CUCM control?  What are  the rules on content sharing inside a video conference? 

New Member

Re: Cisco Jabber for Windows can place Point to Point Video Call

No BFCP screen sharing support for PVDM3.
Active speaker presentation.

Add the resource the UCM just like an Xcode or conf bridge.

Sent from Cisco Technical Support iPhone App

Bronze

Cisco Jabber for Windows can place Point to Point Video Call but

Were you able to figure this out?  I've yet to find any documentation officially noting support for Jabber on the PVDM3's, but it "sounds" like it should work OK via MRGL.

New Member

Am experiencing  the same

Am experiencing  the same issue; I can make point-to-point video calls on Jabber but having issues making video conference calls even after I configured video conference bridge via an ISR router and also have an MCU set-up as well.

 

Any ideas on what to check next?

New Member

Cisco Jabber for Windows can place Point to Point Video Call but

I even created a separate profile for 720p video which jabber uses as shown below, but still no go.

Has anyone been able to get Jabber for windows video conference working?

dspfarm profile 2 conference video homogeneous 

codec g711ulaw

codec g711alaw

codec g729ar8

codec g729abr8

codec g729r8

codec g729br8

codec h264 720p frame-rate 30 bitrate 2mbps

maximum conference-participants 8

maximum sessions 4

associate application SCCP

New Member

Cisco Jabber for Windows can place Point to Point Video Call but

Hi,

Are there any config example?

I have a MCU and I want to integrate Jabber and MCU for Multiparty Video Call.

Thanks

Cisco Jabber for Windows can place Point to Point Video Call but

I have the same problem for making multi party video call using CUCM 7.1.5, Meeting Place 8.6 as conference bridge and cisco Jabber 9.2.3.

Point to point video is ok but when the third party is added it becomes a audio call. Any suggestions Please??

Thank you.

New Member

Hi, Just wondering if you

Hi,

 

Just wondering if you managed to fix this problem?

6013
Views
0
Helpful
12
Replies
CreatePlease login to create content