Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

10 gig module

Hi,

Is it possible to connect a 10 GIG SFP module(multimode) in the below 4503 switch. Is it compatible with the below switch...

 

cisco WS-C4503-E (MPC8245) processor (revision 4) with 262144K bytes of memory.
Processor board ID SPE120700HU
MPC8245 CPU at 267Mhz, Supervisor II+TS
Last reset from Reload
7 Virtual Ethernet interfaces
20 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

 

NAME: "Switch System", DESCR: "Cisco Systems, Inc. WS-C4503-E 3 slot switch "
PID: WS-C4503-E        , VID: V01, SN: SPE120700HU

NAME: "Linecard(slot 1)", DESCR: "Supervisor II+TS with 12 10/100/1000BaseT RJ45
V voice powerports, and 8 1000Bas"
PID: WS-X4013+TS       , VID: V07, SN: JAE1111950X

NAME: "GigabitEthernet1/13", DESCR: "1000BaseSX"
PID: SFBR-5766PZ       , VID:    , SN: AGM12091C60

NAME: "GigabitEthernet1/14", DESCR: "1000BaseSX"
PID: QFBR-5766LP       , VID:    , SN: AGS094756P6

NAME: "GigabitEthernet1/15", DESCR: "1000BaseT"
PID: ABCU-5710RZ-CS2   , VID:    , SN: AGM121220LX

NAME: "GigabitEthernet1/17", DESCR: "1000BaseT"
PID: SP7041_Rev_F      , VID: F  , SN: 00000MTC15200CMT

NAME: "GigabitEthernet1/19", DESCR: "1000BaseSX"
PID: FTRJ8519P1BNL     , VID: A  , SN: FNS104WD2P4

NAME: "GigabitEthernet1/20", DESCR: "1000BaseSX"
PID: SFBR-5766PZ-CS1   , VID:    , SN: AGM142314TE

NAME: "Fan", DESCR: "FanTray"
PID: WS-X4593-E        , VID: V01, SN: SPE120700CM

NAME: "Power Supply 1", DESCR: "Power Supply ( AC 1300W )"
PID: PWR-C45-1300ACV   , VID:    , SN: SNI0849AR7B

NAME: "Power Supply 2", DESCR: "Power Supply ( AC 1300W )"
PID: PWR-C45-1300ACV   , VID: V04, SN: SNI1046ARA2


Thanks & Regards,

M.Mohamed Raffiudeen...

7 REPLIES

I think 10G is not supported.

I think 10G is not supported. You should advice the product page as well.

 Hi,Do we need to upgrade

 

Hi,

Do we need to upgrade this switch?

Pls let me know what should we do to install 10 gig module...

Regards,

 

Please provide the show

Please provide the show module command output.

Hi,Pls find the output...WS

Hi,

Pls find the output...

WS_AJVA_4503_CORE#sh module
Chassis Type : WS-C4503-E

Power consumed by backplane : 0 Watts

Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
 1    20  Sup II+TS 10/100/1000BaseT (RJ45), SFP WS-X4013+TS        JAE1111950X

 M MAC addresses                    Hw  Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
 1 001f.6cd1.eac0 to 001f.6cd1.ead3 1.7 12.2(20r)EW1 12.2(44)SG       Ok

WS_AJVA_4503_CORE#

 

Regards,

If I am not wrong you have a

If I am not wrong you have a left module on the chassis, is that right? So you have install a module that supports 10G interfaces? I think for 4500 series there is one line card supporting 6 (or 12) TenG interfaces. 

Hi,Tnx for your time.10G line

Hi,

Tnx for your time.

10G line card is not supported and we have been tool to upgrade to 4506 E.

 

Thanks & Regards...

Hall of Fame Super Gold

Is it possible to connect a

Is it possible to connect a 10 GIG SFP module(multimode) in the below 4503 switch.

Why would you want to do that?  the 4503-E chassis can't support more than 6 Gbps per slot. 

 

You may want to upgrade to a 4500R+E chassis and get a bundle (which includes the supervisor card).

109
Views
0
Helpful
7
Replies
CreatePlease login to create content