Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

1941 Router Rommon Mode recory problem (Interface GE 0 link down)

Dear Friend,

i am try to recover my Router (1941 with serial Card) from rommon mode prosses is below but problem is there showing error (Interface GE 0 link down) i am also try with both cable like cross and streght but problem is still there Note :- Ge0/0 prot was up in Boot time i have also attach Router Log file in atach file 

rommon 1 > IP_ADDRESS=192.168.1.1

rommon 2 > IP_SUBNET_MASK=255.255.255.0

rommon 3 > DEFAULT_GATEWAY=192.168.1.1

rommon 4 > TFTP_SERVER=192.168.1.32

rommon 5 > TFTP_FILE=c1700-k9sv8y7-mz.122-15.T14.bin

rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.1

      IP_SUBNET_MASK: 255.255.255.0

     DEFAULT_GATEWAY: 192.168.1.1

         TFTP_SERVER: 192.168.1.32

           TFTP_FILE: c1700-k9sv8y7-mz.122-15.T14.bin

        TFTP_MACADDR: e0:5f:b9:a2:69:a0

    TFTP_DESTINATION: flash0:

             GE_PORT: Ge0/0

     TFTP_MEDIA_TYPE: Copper

        TFTP_VERBOSE: Progress

    TFTP_RETRY_COUNT: 18

        TFTP_TIMEOUT: 7200

       TFTP_CHECKSUM: No

       GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.

WARNING: all existing data in all partitions on flash will be lost!

Do you wish to continue? y/n:  [n]:  y

Interface GE 0 link down

TFTP: Operation terminated prematurely.

10 REPLIES
New Member

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

I have also try with new Image file

(c1900-universalk9-mz.SPA.152-4.M4.bin)

rommon 1 > IP_ADDRESS=192.168.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=192.168.1.1
rommon 4 > TFTP_SERVER=192.168.1.32
rommon 5 > TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.1
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 192.168.1.1
         TFTP_SERVER: 192.168.1.32
           TFTP_FILE:c1900-universalk9-mz.SPA.152-4.M4.bin

TFTP_MACADDR: e0:5f:b9:a2:69:a0
    TFTP_DESTINATION: flash0:
             GE_PORT: Ge0/0
     TFTP_MEDIA_TYPE: Copper
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
       GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n:  [n]:  y

Interface GE 0 link down
TFTP: Operation terminated prematurely.

VIP Purple

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

Hi ,

I was having same problem to load the IOS, I think it will be good for you to load ios from xmodem.

http://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a008015bfac.shtml

Step 1: rommon 12 > xmodem -cfs115200 c1900-universalk9-mz.SPA.152-4.M4.bin

Step2 :Select Transfer and Send File from the HyperTerminal menu bar. (see the link)

it will take long time

Regards

New Member

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

Dear ,

I Have try with Xmodem prosses but problem is still there

NOTE:- Router Model 1941

Hall of Fame Super Gold

1941 Router Rommon Mode recory problem (Interface GE 0 link down

Afroz,

This is a DUPLICATE thread to this.

As I have pointed this out to you in your other thread, you are trying to load an IOS for a 1700 router into your 1900 router.

And this, I can assure you, will not work.

NOTE:  You will be able to copy the file into the 1900 router but that's where it ends.

New Member

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

Dear Leo Laohoo

I Habe try with

c1900-universalk9-mz.SPA.152-4.M4.bin but problem is still there problem with Ge0/0 port  wich is taken by default

but when we try to give ip by below mention method but ge0 port is not coming Up

rommon 1 > IP_ADDRESS=192.168.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=192.168.1.1
rommon 4 > TFTP_SERVER=192.168.1.32
rommon 5 > TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

rommon 6 > tftpdnld

          IP_ADDRESS: 192.168.1.1
      IP_SUBNET_MASK: 255.255.255.0
     DEFAULT_GATEWAY: 192.168.1.1
         TFTP_SERVER: 192.168.1.32
           TFTP_FILE:c1900-universalk9-mz.SPA.152-4.M4.bin

TFTP_MACADDR: e0:5f:b9:a2:69:a0
    TFTP_DESTINATION: flash0:
             GE_PORT: Ge0/0
     TFTP_MEDIA_TYPE: Copper
        TFTP_VERBOSE: Progress
    TFTP_RETRY_COUNT: 18
        TFTP_TIMEOUT: 7200
       TFTP_CHECKSUM: No
       GE_SPEED_MODE: 1000MB/FULL

Invoke this command for disaster recovery only.
WARNING: all existing data in all partitions on flash will be lost!
Do you wish to continue? y/n:  [n]:  y

Interface GE 0 link down
TFTP: Operation terminated prematurely.

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

hi,

i think you should set your DEFAULT_GATEWAY and TFTP_SERVER to be on same IP address with your PC/laptop.

try to make it simple and use 192.168.1.2. using a straight cable should be no problem.

New Member

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

Dear,

I have given IP Address in below step

Router IP

IP_ADDRESS=192.168.1.1

Subnet Mask

IP_SUBNET_MASK=255.255.255.0

Default Gateway

DEFAULT_GATEWAY=192.168.1.1

PC IP IS

TFTP_SERVER=192.168.1.32

Image File Name

TFTP_FILE=c1900-universalk9-mz.SPA.152-4.M4.bin

Hall of Fame Super Gold

1941 Router Rommon Mode recory problem (Interface GE 0 link down

Afroz,

1.  Power down the router;

2.  Eject the CF;

3.  Get a multi-card reader;

4.  Use a PC to copy the IOS from your PC to the CF using the multi-card reader;

5.  Insert the CF back to the router.

6.  Power on the router.

Please don't forget to rate our useful posts. 

New Member

Re: 1941 Router Rommon Mode recory problem (Interface GE 0 link

Dear ,

Ge0/0 Port is enbelt in Router Mother Board it it not posibale to remove the Ge0/0 Port from the router

New Member

hi Afroz,i think that you

hi Afroz,

i think that you have problem with speed, be sure that the speed of the network card from the laptop or PC is 1 GB, else you must set speed to 100, with command GE_SPEED_MODE:

1926
Views
0
Helpful
10
Replies