Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

I am really new with the use of the SLM2008 , but it can already do much more that I have expected .

The reason for this post is :

I have in the IT room 2 networks : One is on a IP Range : 10.0.0.x subnet mask 255.255.255.0

The other is on IP Range : 192.168.1.x subnet mask 255.255.255.0

If I connect the first network to PORT 2 and the second to PORT 3

connect a CAT6 cable to PORT 8

50Meters away , I would like to also put a SLM2008 where I will connect the above CAT6 cable to PORT 8 and retrieve back my to LAN's on PORT 2 and 3.

Is this possible ?

10.0.0.x          :PORT 2 :------------ :                                                                :---------------: PORT 2 : 10.0.0.x

                                                  |PORT 8----------------CAT6-----------------PORT8|

192.168.1.x     :PORT 3 :------------ :                                                                :---------------: PORT 3 : 192.168.1.x

I think it is possible , but I do not know how

Thank you for your help and Best Regards,

Didier.

2 ACCEPTED SOLUTIONS

Accepted Solutions
VIP Super Bronze

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello Didier,

|PORT 8----------------CAT6-----------------PORT8

Since you have 2 VLANs on each side, make the Cat6 link (port 8) between your switchs a trunk link so you can carrry both VLANs

switchport mode trunk
switchport trunk encapsulation dot1q

switchport trunk allowed vlan xx

HTH

Reza

Hall of Fame Super Blue

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Didier1966 wrote:

Hello,

How do you make a trunk with a SLM2008 ?

Is this possible ? I can not find it in the manual

Best Regards,

Didier.

See page 7/8  of the attached doc - specifically the bit about VLAN Port settings.

Jon

9 REPLIES
VIP Super Bronze

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello Didier,

|PORT 8----------------CAT6-----------------PORT8

Since you have 2 VLANs on each side, make the Cat6 link (port 8) between your switchs a trunk link so you can carrry both VLANs

switchport mode trunk
switchport trunk encapsulation dot1q

switchport trunk allowed vlan xx

HTH

Reza

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

Thank you for your prompt reply

Best Regards,

Didier.

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

How do you make a trunk with a SLM2008 ?

Is this possible ? I can not find it in the manual

Best Regards,

Didier.

Hall of Fame Super Blue

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Didier1966 wrote:

Hello,

How do you make a trunk with a SLM2008 ?

Is this possible ? I can not find it in the manual

Best Regards,

Didier.

See page 7/8  of the attached doc - specifically the bit about VLAN Port settings.

Jon

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hi Jon,

Thank you for your prompt reply

My problem was , I was looking for the word TRUNK , but it did not guide me to a page , but when I read more carefully I understand it know the meaning of trunk.

It will be fine for beginners like me to put the word trunk between brackets "Trunk Mode"

Best Regards,

Didier

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

When one of you find the time , can you give me a working example

I have 2 SLM2008 and 2 WRT610N on my desk.

The first WRT610N is on IP 10.0.0.1

The second WRT610N is on IP 192.168.1.1

I would like to merge both WRT610N via a SLM2008 to a second SLM2008 and have them back on the other side.

WRT610N 10.0.0.1           : PORTx                                                                                                    PORTx : DHCP in the range of 10.0.0.x

                                                           PORTz SLM2008  ----------------------------- PORTz SLM2008

WRT610N 192.168.1.1     : PORTy                                                                                                    PORTy : DHCP in the range of 192.168.1.x

Any help is welcome.

How more I read about VLANS , how less I understand

Thank you in advance

Best Regards,

Didier.

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello Reza,

Thank you again for your prompt reply

Is it possible on the SLM2008 , to make a configuration has a text like you just show.

switchport mode trunk
switchport trunk encapsulation dot1q

switchport trunk allowed vlan xx

I use the GUI to program SLM2008.

Thank you for your help,

Best Regards,

Didier

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

I am still struggling with my 2 SLM2008.

How more I read about the subject , how less I start to understand

Can it be that to use the trunk mode on the SLM2008 , I need CAT OS ?

Is this CAT OS , free ?

Thank you again for your help

Best Regards,

Didier.

Community Member

Re: 2 VLANS on one site over 1 CAT6 to a other site ?

Hello,

Just to tell you that I managed to make it work

The only thing that they have to add in the user manual , is that you can only trunk on a SLM2008 on PORT 1 !!!

All my test I did , where on port 8, and this do not work.

Thank you all for your time.

Best Regards,

Didier.

760
Views
0
Helpful
9
Replies
CreatePlease to create content