Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

2811v network module

Dear All,

i have question about router 2811,

for now, all HWIC in 2811 is full,

Slot 0 : VIC2-2E/M

Slot 1 : VIC2-2E/M

Slot 2 :  WIC-1T=

Slot 3 :  HWIC-1FE

but we need add more 2 module VIC3-2E/M. can we use Network Module ?

example : add one NM-HD-2V + two VIC3-2E/M ?

please give me an info,can we do that? and whether it is the same as we use the VIC2-2E / M on HWIC slots

  • LAN Switching and Routing
Everyone's tags (6)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

2811v network module

Hello Leornadus,

I do not see any restriction adding a Network module in your 2811 with the two VICs you mentioned or any hardware limitation for the utilization of all these VIC/HWIC combinaison =>

The different Cisco links states Cisco 2811 supports : 4 HWIC slots, 1 expansion network module slot, 2 PVDM slots, 2 AIM slots

As you suggested NM-HD-2V-(E in function of the needs) is the most appropriate choice in your scenario and supports two VIC3-2E/M =>

http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet09186a00800921e7_ps3115_Products_Data_Sheet.html

Minimum release for VIC3-2E/M is 12.4(20)T (or 12.4(15)XW) in « ipvoice IOS »– Table 4 (and 10) http://www.cisco.com/en/US/prod/collateral/modules/ps5365/product_data_sheet0900aecd801c595e.html

The VIC3 utilization in a NM should be the same as if it was in a HWIC slot exept the interface naming will change => The NM-HD-2V will be changed to slot 1/x/y (instead of 0/./.)

Please note your already existing VIC-2E/M are not supported in the Cisco IP Communications Voice/Fax Network Modules (NM-HD-1V, NM-HD-2V and NM-HD-2VE).

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094ab9.shtml#productnumbers

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094ab9.shtml#productnumbershttp://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml

As you may guess if you add this NM (with 2 VICs) there will be no more room in the 2811 :-)

And if another evolution is needed (!!!) either you can upgrade the hardware to a more large 28xx platform..Or to a ISR2 but in this case you will have to reconsider the complete compatibility matrix (another story …)..

I would also pay attention to the PVDM-2 requirments with the introduction of the NM and 2 VIC3-E/M (but I think the best if some information is needed on this would be to post in IP Telephony area in this case)…

Hope that helps.

Kind regards.

Karim

2 REPLIES
Silver

2811v network module

Hello Leornadus,

I do not see any restriction adding a Network module in your 2811 with the two VICs you mentioned or any hardware limitation for the utilization of all these VIC/HWIC combinaison =>

The different Cisco links states Cisco 2811 supports : 4 HWIC slots, 1 expansion network module slot, 2 PVDM slots, 2 AIM slots

As you suggested NM-HD-2V-(E in function of the needs) is the most appropriate choice in your scenario and supports two VIC3-2E/M =>

http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet09186a00800921e7_ps3115_Products_Data_Sheet.html

Minimum release for VIC3-2E/M is 12.4(20)T (or 12.4(15)XW) in « ipvoice IOS »– Table 4 (and 10) http://www.cisco.com/en/US/prod/collateral/modules/ps5365/product_data_sheet0900aecd801c595e.html

The VIC3 utilization in a NM should be the same as if it was in a HWIC slot exept the interface naming will change => The NM-HD-2V will be changed to slot 1/x/y (instead of 0/./.)

Please note your already existing VIC-2E/M are not supported in the Cisco IP Communications Voice/Fax Network Modules (NM-HD-1V, NM-HD-2V and NM-HD-2VE).

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094ab9.shtml#productnumbers

http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a0080094ab9.shtml#productnumbershttp://www.cisco.com/en/US/products/hw/routers/ps259/products_tech_note09186a00800e73f6.shtml

As you may guess if you add this NM (with 2 VICs) there will be no more room in the 2811 :-)

And if another evolution is needed (!!!) either you can upgrade the hardware to a more large 28xx platform..Or to a ISR2 but in this case you will have to reconsider the complete compatibility matrix (another story …)..

I would also pay attention to the PVDM-2 requirments with the introduction of the NM and 2 VIC3-E/M (but I think the best if some information is needed on this would be to post in IP Telephony area in this case)…

Hope that helps.

Kind regards.

Karim

New Member

2811v network module

thank you Karim, very helped.

regards.

722
Views
0
Helpful
2
Replies