Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

2924 - switch#show Ip

Hello,

When I type this command in by using hyperterminal I get the Ip address of 1.

Can anyone explain to me why? I am new in the cisco world and could use your help.

Thanks,

Lon

6 REPLIES

Re: 2924 - switch#show Ip

can you make your question more brief?

New Member

Re: 2924 - switch#show Ip

can u paste the output of the command plz

Re: 2924 - switch#show Ip

Hi,

When doing the command "show ip" on a layer 2 switch it shows the number of the management VLAN as illustrated below (which should be 1 by default, any way try changing it as follows):

SW3#sh ip int brief | i VLAN

VLAN1 unassigned NO unset up down

VLAN13 1.1.1.1 YES manual up up

SW3#sh ip

13

HTH,

Mohammed Mahmoud.

New Member

Re: 2924 - switch#show Ip

Thanks a bunch,

From your reply I was able to figure out how to change the ip address, but unfortunately when I turned it off it went back to the orginal. I tried to run the command: copy running-config startup-config, but it did not like it. I have a cisco book and have passed the CNA 5 years ago, but I forgot all of it because the lack of having anything to play with. Is there a place to go to find proper commands for certain devices? Do you know the command I need to save my changes for this 2924 switch? The total memory is not quite 4mb if I am reading this right. Is that what you see?

This is what I am looking at so far:

Switch-4385#show memory

Head Total(b) Used

(b) Lowest(b) t(b)

Processor 45FF1C 3801316 1749908 2051408 1778828 1773128

I/O 70000000 1048576 606784 441792 328436 425692

Switch-4385#show ip

1

Switch-4385#show ip interface brief vlan1

Interface IP-Address OK? Method Status Prot

ocol

VLAN1 10.0.16.9 YES NVRAM up up

Switch-4385(config)#interface vlan1

Switch-4385(config-if)#ip address 10.0.16.1 255.255.255.0

Switch-4385(config-if)#exit

Switch-4385(config)#exit

Switch-4385#

Switch-4385#show interface vlan1

VLAN1 is up, line protocol is up

Hardware is CPU Interface, address is 0002.b977.e440 (bia 0002.b977.e440)

Internet address is 10.0.16.1/24

MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation ARPA, loopback not set

ARP type: ARPA, ARP Timeout 04:00:00

Last input never, output 00:00:50, output hang never

Last clearing of "show interface" counters never

Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 throttles

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored

0 input packets with dribble condition detected

9 packets output, 576 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collision, 0 deferred

0 lost carrier, 0 no carrier

0 output buffer failures, 0 output buffers swapped out

Re: 2924 - switch#show Ip

Here's the link to Cat 2900 switch configuration guide.

http://www.cisco.com/en/US/docs/switches/lan/catalyst2900xl_3500xl/release12.0_5_wc6/scg/scg.html

HTH

Sundar

New Member

Re: 2924 - switch#show Ip

Thanks,

Now I have some studing to do.

Have a good day!

Lon

406
Views
0
Helpful
6
Replies
CreatePlease to create content