Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k

2960 logging trap 6 issue

Hi ,

Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands .

the steps used to configure -

sw(confg)#loggig trap 6

sw(config)#exit

sw#wr

sw#show runn | i logging

sw#       --------------> (no match)

after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .

I tried the same on 12.55.SE release also but its same results .Please let me know is this a limitaion of this platform, is there any doc explaining the same for reference .

sh ver snap from switch-

SW2 uptime is 2 days, 5 hours, 3 minutes

System returned to ROM by power-on

System restarted at 08:29:28 IST Sat May 26 2012

System image file is "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin"

cisco WS-C2960G-24TC-L (PowerPC405) processor (revision F0) with 61440K/4088K bytes of memory.

Last reset from power-on

1 Virtual Ethernet interface

24 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

64K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 00:26:51:48:BA:00

Motherboard assembly number     : 73-10015-07

Power supply part number        : 341-0098-02

--More--                           Model revision number           : F0

Motherboard revision number     : A0

Model number                    : WS-C2960G-24TC-L

System serial number            :

Top Assembly Revision Number    : B0

Version ID                      : V04

CLEI Code Number                : COMFX00BRA

Hardware Board Revision Number  : 0x01

Switch Ports Model              SW Version            SW Image                

------ ----- -----              ----------            ----------              

*    1 24    WS-C2960G-24TC-L   12.2(44)SE6           C2960-LANBASEK9-M       

Configuration register is 0xF

SHCIL-MHDC-Ext-SW2#sh fil

SHCIL-MHDC-Ext-SW2#sh file sy

SHCIL-MHDC-Ext-SW2#sh file systems

File Systems:

     Size(b)     Free(b)      Type  Flags  Prefixes

*   32514048    22090240     flash     rw   flash:

           -           -    opaque     rw   vb:

=========

Thanks for reply

Everyone's tags (4)
1 ACCEPTED SOLUTION

Accepted Solutions
Silver

2960 logging trap 6 issue

Hi,

The default trap level is "informational" and as such it is not displayed in the config file. Please see the reference for 12.2 IOS beneath:

http://www.cisco.com/en/US/docs/ios/12_2/debug/command/reference/dbfintro.html#wp1017299

You can check the trap level configured via the "sh logging" command.

Best regards,

Antonin

1 REPLY
Silver

2960 logging trap 6 issue

Hi,

The default trap level is "informational" and as such it is not displayed in the config file. Please see the reference for 12.2 IOS beneath:

http://www.cisco.com/en/US/docs/ios/12_2/debug/command/reference/dbfintro.html#wp1017299

You can check the trap level configured via the "sh logging" command.

Best regards,

Antonin

611
Views
0
Helpful
1
Replies
CreatePlease to create content