Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

2960 rommon tftp?

Does the 2960 support tftp when it rommon mode? Can you set a 2960 to download it's image from a tftp server? If not is there any other way to get he bin file on the switch without waiting for xmodem?

Thanks

2 ACCEPTED SOLUTIONS

Accepted Solutions

Re: 2960 rommon tftp?

Unfortunately TFTP is not supported in rommon on the 2960 switch. You will have to use xmodem to load an IOS to the switch. There is a much faster way to upload the IOS. It will take minutes instead of hours.

http://www.cisco.com/en/US/products/hw/switches/ps628/products_tech_note09186a0080169696.shtml#speedrecovery

HTH,

mark

Re: 2960 rommon tftp?

not possible by tftp you need to download image via xmodem if switch has corrupted image or deleted image.

switch: copy xmodem: flash:image_filename.bin

Go over this link - using xmodem

http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_40_se/configuration/guide/swtrbl.html#wp1099467

Rgds

Jorge

11 REPLIES

Re: 2960 rommon tftp?

Unfortunately TFTP is not supported in rommon on the 2960 switch. You will have to use xmodem to load an IOS to the switch. There is a much faster way to upload the IOS. It will take minutes instead of hours.

http://www.cisco.com/en/US/products/hw/switches/ps628/products_tech_note09186a0080169696.shtml#speedrecovery

HTH,

mark

New Member

Two years ago when I was a

Two years ago when I was a technician an engineer showed me how to unbrick a 2960 and I never used xmodem. I only used tftp so their is a way. In fact I installed a 3750 ios on a 2960 and all I had was Romon mode. I'm trying to duplicate what I did on my 2960 but its been two years and I can't remember all the steps. I've never used xmodem in my life. I'll update this post if I figure it out. 

Richard

Hall of Fame Super Gold

There is no way other than

There is no way other than XModem on a 2960/2960G and/or 3750/3750G because these models neither have a USB port nor "tftpdnld" command.  With the newer switch that come with a USB port, it is as simple as plugging a valid USB thumb drive with the IOS BIN file.

New Member

I just read a post where

I just read a post where someone booted an IOS from a tftp server and then installed the image. Their comment was why does cisco only put in the documentation one way of doing things (Xmodem) when their are three ways. and they pick the most conveluted way. He was working with a 2960.

I'm telling you I unbricked several 2960 switches and I never used xmodem.

New Member

I realize this is an old

I realize this is an old thread and marked as answered, but I believe the answer is incorrect. You can do it via TFTP, here is how:

Initialize the flash:
switch: flash_init

Initialize the management interface:
switch: mgmt_init

Then assign an IP address to the management interface:
switch: set IP_ADDR 10.1.100.2/255.255.255.0
switch: set DEFAULT_ROUTER 10.1.100.1

Then configure your TFTP server to have an IP on the same subnet and connect it to the management interface of the switch (ie 10.1.100.1/24)

Now to tell the switch to retrieve the firmware image:
switch: copy tftp://10.1.100.1/c2960x-universalk9-mz.152-5b.E.bin flash:c2960x-universalk9-mz.152-5b.E.bin

The switch should then retrieve the image and save it flash.

Once the copy is complete boot from it with:

switch: boot flash:c2960x-universalk9-mz.152-5b.E.bin

Note: Connect your Laptop/TFTP server/whatever to the Management Interface of the switch

New Member

Thank you! You saved me from

Thank you! You saved me from Xmodem hell!

This is really the CORRECT ANSWER!

Is it possible to have the above post marked as the correct answer?

Thanks again!

Re: 2960 rommon tftp?

not possible by tftp you need to download image via xmodem if switch has corrupted image or deleted image.

switch: copy xmodem: flash:image_filename.bin

Go over this link - using xmodem

http://www.cisco.com/en/US/docs/switches/lan/catalyst2960/software/release/12.2_40_se/configuration/guide/swtrbl.html#wp1099467

Rgds

Jorge

New Member

Re: 2960 rommon tftp?

Does anyone know why this feature isn't available? It gives you the options to set an ip address, gateway and an tftp server but not the tftpdnld command. I guess it is just as bad to not have enough space for two images at the same time...

Thanks guys.

Purple

Re: 2960 rommon tftp?

If you change the console speed to 115200 a 2960 image will take maybe 5-6 minutes , its a big difference from 9600 .

New Member

While writting this comment i

While writting this comment i just (im sitting in front of a rack and) succesfully unbricked a 2960x with following Manual:

http://blog.unolution.com/networking/how-to-recover-a-cisco-switch-3560x-3750x-from-boot-loader/

Yes a 2960x! 

worked perfectly..

cheers

Pete

Hall of Fame Super Gold

Not the same.  2960/2960G

Not the same.  2960/2960G does NOT have a USB port while the 2960S/X have.  If a 2960S/X boots up in ROMmon because of a failure of the IOS, use a USB thumb drive to boot the IOS works very well. 

13652
Views
20
Helpful
11
Replies
CreatePlease to create content