Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

2960(S) HSRP support

Hi, the 2960 series  with LAN Base image now supports a limited L3-routing functionality.

I tried to test if HSRP also works, and surprise, it works.

Because I do not find any document with infos thats HSRP is official supported on the 2960, does naybody have knowledge

if its officialy supported or it "just" works.



switch#sh sdm prefer

The current template is "lanbase-routing" template.

The selected template optimizes the resources in

the switch to support this level of features for

8 routed interfaces and 255 VLANs.

  number of unicast mac addresses:                  4K

  number of IPv4 IGMP groups + multicast routes:    0.25K

  number of IPv4 unicast routes:                    4.25K

    number of directly-connected IPv4 hosts:        4K

    number of indirect IPv4 routes:                 0.25K

  number of IPv4 policy based routing aces:         0

  number of IPv4/MAC qos aces:                      0.125k

  number of IPv4/MAC security aces:                 0.375k


switch(config)#ip routing


switch#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2

       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

       ia - IS-IS inter area, * - candidate default, U - per-user static route

       o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C is directly connected, Vlan199 is subnetted, 4 subnets

C is directly connected, Vlan300

C is directly connected, Vlan301

C is directly connected, Vlan302

C is directly connected, Vlan303


interface Vlan300

ip address

standby 100 ip

standby 100 priority 200

standby 100 preempt delay minimum 60


interface Vlan301

ip address

standby 101 ip

standby 101 priority 200

standby 101 preempt delay minimum 60


interface Vlan302

ip address

standby 102 ip

standby 102 priority 200

standby 102 preempt delay minimum 60


interface Vlan303

ip address

standby 103 ip

standby 103 priority 200

standby 103 preempt delay minimum 60


switch#sh stand brief

                     P indicates configured to preempt.


Interface   Grp  Pri P State   Active          Standby         Virtual IP

Vl300       100  200 P Active  local 

Vl301       101  200 P Active  local 

Vl302       102  200 P Active  local 

Vl303       103  200 P Active  local 


router#sh stand brief

                     P indicates configured to preempt.


Interface   Grp  Pri P State   Active          Standby         Virtual IP

Vl300       100  150 P Standby     local 

Vl301       101  150 P Standby     local 

Vl302       102  150 P Standby     local 

Vl303       103  150 P Standby     local 


switch#sh ver

Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(55)SE1, RELEASE SOFTWARE (fc1)

Technical Support:

Copyright (c) 1986-2010 by Cisco Systems, Inc.

Compiled Thu 02-Dec-10 08:16 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x01800000

ROM: Bootstrap program is C2960 boot loader

BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(35r)SE2, RELEASE SOFTWARE (fc1)

switch uptime is 56 minutes

System returned to ROM by power-on

System image file is "flash:/c2960-lanbasek9-mz.122-55.SE1/c2960-lanbasek9-mz.122-55.SE1.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

If you require further assistance please contact us by sending email to

cisco WS-C2960G-8TC-L (PowerPC405) processor (revision A0) with 65536K bytes of memory.

Processor board ID FOC1331V58Q

Last reset from power-on

6 Virtual Ethernet interfaces

8 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

64K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 00:26:CA:8C:20:00

Motherboard assembly number     : 73-10613-08

Power supply part number        : 341-0208-01

Motherboard serial number       : FOC13311MZK

Power supply serial number      : LIT132806DR

Model revision number           : A0

Motherboard revision number     : B0

Model number                    : WS-C2960G-8TC-L

System serial number            : FOC1331V58Q

Top Assembly Part Number        : 800-28133-01

Top Assembly Revision Number    : E0

Version ID                      : V01

CLEI Code Number                : COM7S00ARA

Hardware Board Revision Number  : 0x01

Switch Ports Model              SW Version            SW Image

------ ----- -----              ----------            ----------

*    1 8     WS-C2960G-8TC-L    12.2(55)SE1           C2960-LANBASEK9-M

Configuration register is 0xF


Hall of Fame Super Silver

Re: 2960(S) HSRP support


I used the Feature Navigator from the Cisco web site ( to find the features supported in your version of code for the 2960. According to the Feature Navigator HSRP is an officially supported feature in your version of code for the 2960.



New Member

Re: 2960(S) HSRP support

Hi Richard,

I know that feature navigator shows HSRP as supported with 2960, but to be honest FN ist not always perfekt and configuring HSRP on the

SVI cannot be found in any 2960 configuration guide!?!

So I am afraid that it "just" works ?



New Member

2960(S) HSRP support


Configuration of HSRP on pair of standalone 2960-S under 12.2.55SE2 caused instability and reloads of catalysts early after deployment. We must remove it from configuration.

Answer from Cisco BU was: HSRP is not supported feature on 2960-S.

Best Regards


2960(S) HSRP support

Hi Hubert,

I do not see this feature (HSRP) listed in Cisco feature navigator for catalyst 2960 line. I tried it over a year ago on 2960 and as Karel writes it caused instability issues. And yes it is just working, maybe for some configurations and topologies (needs extensive testing, which I have not perform). I would not recommend for production network.




2960(S) HSRP support

   That is true just because it was left in the code doesn't mean its supported.  I remember on some Cat 4500's with SupII pluses with ipbase software you  could get BGP to work and peer with other devices but it was not supported .