3560 policy based routing verify-availability

[mukremin13]

Cisco 3560 does not support "set ip next-hop verify-availabilty". I need this command in my config. "set ip next-hop"  do not do the same job.

What can i do?

any other related command in replace of it?

[danbowencisco]

Hi There,

It does support it, I have it on my 3560G.

What version of code are you running?

Dan

[mukremin13]

SW version 12.2.(50)SE3

Sw image C3560-IPSERVICESK9-M

and switch hardware 3560v2

[danbowencisco]

ok, upgrade to the following as you can see that it is supported on my 3560G

route-map PBR-Management permit 30
match ip address Route-Map-ACL-Management-Process3
set ip next-hop verify-availability 10.11.120.161 1 track 30

Cisco IOS Software, C3560 Software (C3560-IPSERVICESK9-M), Version 12.2(58)SE2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 21-Jul-11 01:44 by prod_rel_team

ROM: Bootstrap program is C3560 boot loader
BOOTLDR: C3560 Boot Loader (C3560-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)

SL-Cisco-3560G-SW uptime is 12 hours, 36 minutes
System returned to ROM by power-on
System image file is "flash:c3560-ipservicesk9-mz.122-58.SE2.bin"

[mukremin13]

Yes in my ios there is also this config shown. But when i insert another sequence like

"route-map PBR-Management permit 40", debug says unsupported.

Do you have many sequence with the same name. Like

route-map PBR-Management permit 30

route-map PBR-Management permit 40

route-map PBR-Management permit 50

And is it running correctly?

And also this link says set ip next-hop verify-availability is not supported.

http://www.cisco.com/en/US/docs/switches/lan/catalyst3560/software/release/12.2_58_se/configuration/guide/swuncli.html

[danbowencisco]

yes I do jave the sequence, as shown below - one problem I am having is getting the route map on the interface as it allows the command but doesnt show the route map in the config.

route-map PBR-Management permit 10

match ip address Route-Map-ACL-Management-Process1

set ip next-hop verify-availability 10.11.120.161 1 track 610

!

route-map PBR-Management permit 20

match ip address Route-Map-ACL-Management-Process2

set ip next-hop verify-availability 10.11.120.161 1 track 620

!

route-map PBR-Management permit 30

match ip address Route-Map-ACL-Management-Process3

set ip next-hop verify-availability 10.11.120.161 1 track 630

!

route-map PBR-Management permit 40

match ip address Route-Map-ACL-Management-Information

set ip next-hop verify-availability 10.11.120.161 1 track 640

!

route-map PBR-Management permit 50

match ip address Route-Map-ACL-Management-Supervisory

set ip next-hop verify-availability 10.11.120.161 1 track 650

route-map PBR-Management permit 10

match ip address Route-Map-ACL-Management-Process1

set ip next-hop verify-availability 10.11.120.161 1 track 610

!

route-map PBR-Management permit 20

match ip address Route-Map-ACL-Management-Process2

set ip next-hop verify-availability 10.11.120.161 1 track 620

!

route-map PBR-Management permit 30

match ip address Route-Map-ACL-Management-Process3

set ip next-hop verify-availability 10.11.120.161 1 track 630

!

route-map PBR-Management permit 40

match ip address Route-Map-ACL-Management-Information

set ip next-hop verify-availability 10.11.120.161 1 track 640

!

route-map PBR-Management permit 50

match ip address Route-Map-ACL-Management-Supervisory

set ip next-hop verify-availability 10.11.120.161 1 track 650

[mukremin13]

same problem with me i think.

I have also do these. But when show running config, there is no ip policy route-map command. And when typing show ip policy it is blank.

when you connect via serial port, and open the "debug ip policy" and set another sequence to the PBR-Management

you have also see unsupported messaage.

[mukremin13]

any update daniel

[mukremin13]

anyone help me?