Cisco Support Community
Showing results for 
Search instead for 
Did you mean: 
New Member

3560QoS and "Service-Policy Input"

Hi Group,

I am trying to use the following QoS policy on Catalyst 3560 (more details attached):


class Voice_Media

set ip dscp 46

police 256000 16000 exceed-action drop

class Nortel_Voice_Signaling

set ip dscp 40

police 32000 8000 exceed-action policed-dscp-transmit

class Cisco_Voice_Signaling

set ip dscp 24

police 32000 8000 exceed-action policed-dscp-transmit

class Security_Camera_Video_Stream

set ip dscp 34

police 500000 16000 exceed-action policed-dscp-transmit

class VTC_Video_Conferencing

set ip dscp 36

police 384000 8000 exceed-action policed-dscp-transmit

class Business_Applications

set ip dscp 26

police 20000000 32000 exceed-action policed-dscp-transmit

class Bulk_Data

set ip dscp 10

police 5000000 8000 exceed-action policed-dscp-transmit

class Scavenger

set ip dscp 8

police 5000000 8000 exceed-action policed-dscp-transmit

class class-default

set ip dscp 0

police 5000000 8000 exceed-action drop


However, when I try to apply the QoS Policy "IPPHONE_WITH_USERPC" it takes my command but it doesn't apply it in the show run:


interface GigabitEthernet0/2

switchport access vlan 4

switchport voice vlan 44

srr-queue bandwidth share 1 70 25 5

srr-queue bandwidth shape 30 0 0 0

priority-queue out

mls qos trust cos

spanning-tree portfast

Can anyone assist me here?

I am using 12.2(35)SE:

Cisco IOS Software, C3560E Software (C3560E-UNIVERSAL-M), Version 12.2(35)SE5, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 19-Jul-07 17:18 by nachen

Image text-base: 0x00003000, data-base: 0x01600000

ROM: Bootstrap program is C3560E boot loader

BOOTLDR: C3560E Boot Loader (C3560E-HBOOT-M) Version 12.2(35r)SE1, RELEASE SOFTWARE (fc2)

ojrpva-s999n-f14 uptime is 14 weeks, 1 day, 4 hours, 15 minutes

System returned to ROM by power-on

System image file is "flash:c3560e-universal-mz.122-35.SE5/c3560e-universal-mz.122-35.SE5.bin"

License Level: ipbase Type: Permanent

Next reboot license Level: ipbase

cisco WS-C3560E-24PD (PowerPC405) processor (revision E0) with 122880K/8184K bytes of memory.

Processor board ID FDO1144V07H

Last reset from power-on

5 Virtual Ethernet interfaces

1 FastEthernet interface

28 Gigabit Ethernet interfaces

2 Ten Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

512K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address : 00:1E:13:D0:93:00

Motherboard assembly number : 73-10318-11

Motherboard serial number : FDO1142073K

Model revision number : E0

Motherboard revision number : B0

Model number : WS-C3560E-24PD-S

Daughterboard assembly number : 800-28590-01

Daughterboard serial number : FDO11320CKJ

System serial number : FDO1144V07H

Top Assembly Part Number : 800-27549-01

Top Assembly Revision Number : C0

Version ID : V01

CLEI Code Number : COM7F10ARA

Hardware Board Revision Number : 0x01

Switch Ports Model SW Version SW Image

------ ----- ----- ---------- ----------

* 1 30 WS-C3560E-24PD 12.2(35)SE5 C3560E-UNIVERSAL-M

Configuration register is 0xF

Thanks in advance...

- Kashif

New Member

Re: 3560QoS and "Service-Policy Input"

You can't apply a trust statement and a policy map to an interface* so I would remove the trust cos statement and then try the service policy statement.

* You can in 12.2.40SE, but the trust statement only applies to traffic not matching the policy map. If you want this behavior, upgrade to that release or later.

CreatePlease to create content