05-17-2012 01:43 PM - edited 03-07-2019 06:46 AM
Hi,
Cisco WS-C3750G-12S at remote location. And the output of show interface is as follows:
sh int gigabitEthernet 1/0/4
GigabitEthernet1/0/4 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 0019.55be.1b04 (bia 0019.55be.1b04)
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is 1000BaseSX SFP ------------> (Is SFP module installed in this interface port?)
Media-type configured as connector
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
Can we know from this output that the interface Gigabit 1/0/4 has been populated by SFP module? (1000BaseSX SFP) or it's just an empty slot that can accomodate the SFP module?
Please share the experience.
Cheers!
Subodh
Solved! Go to Solution.
05-17-2012 02:38 PM
yes, otherwise it will be "media type is Not Present" in the event SFP module is not inserted.
---
Posted by WebUser Neeraj Jagga from Cisco Support Community App
05-17-2012 10:14 PM
bapatsubodh wrote:
Hi,
Cisco WS-C3750G-12S at remote location. And the output of show interface is as follows:
Can we know from this output that the interface Gigabit 1/0/4 has been populated by SFP module? (1000BaseSX SFP) or it's just an empty slot that can accomodate the SFP module?Please share the experience.
Cheers!
Subodh
Yes.
If there was no SFP in the port, it would look like this
sh int g1/1/2
GigabitEthernet1/1/2 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 4055.39de.d532 (bia 4055.39de.d532)
MTU 1500 bytes, BW 10000 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is Not Present
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
[...snipt for brevity...]
Notice the "media type is Not Present"
Cheers.
05-17-2012 02:38 PM
yes, otherwise it will be "media type is Not Present" in the event SFP module is not inserted.
---
Posted by WebUser Neeraj Jagga from Cisco Support Community App
05-17-2012 10:14 PM
bapatsubodh wrote:
Hi,
Cisco WS-C3750G-12S at remote location. And the output of show interface is as follows:
Can we know from this output that the interface Gigabit 1/0/4 has been populated by SFP module? (1000BaseSX SFP) or it's just an empty slot that can accomodate the SFP module?Please share the experience.
Cheers!
Subodh
Yes.
If there was no SFP in the port, it would look like this
sh int g1/1/2
GigabitEthernet1/1/2 is down, line protocol is down (notconnect)
Hardware is Gigabit Ethernet, address is 4055.39de.d532 (bia 4055.39de.d532)
MTU 1500 bytes, BW 10000 Kbit/sec, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Auto-duplex, Auto-speed, link type is auto, media type is Not Present
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
[...snipt for brevity...]
Notice the "media type is Not Present"
Cheers.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide