Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Community Member

3750X phone power issues

I have a mix stack of 3750X/V2's in a network that is getting upgrades.  We just installed new Cisco phones on this stack, and for some reason only the phones on switch 1 are having power problems.  I need some help decoding the log messages.

Basic logs

Aug  9 11:14:04.916 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/13: Power given, but Power Controller does not report Power Good

Aug  9 11:14:04.966 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/16: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.019 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/1: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.061 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/2: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.103 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/3: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.162 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/4: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.238 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/5: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.296 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/6: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.363 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/7: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.430 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/8: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.472 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/9: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.540 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/10: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.581 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/11: Power given, but Power Controller does not report Power Good

Aug  9 11:14:08.623 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/12: Power given, but Power Controller does not report Power Good

Some cable test outputs, yes I do see the short/crosstalk, would that be my issue?  I was told that its possible that was only reported because the cable is in use.

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/13  auto  Pair A     101  +/- 10 meters N/A         Short/Crosstalk

                Pair B     102  +/- 10 meters N/A         Short/Crosstalk

                Pair C     90   +/- 10 meters N/A         Short/Crosstalk

                Pair D     90   +/- 10 meters N/A         Short/Crosstalk

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/14  auto  Pair A     89   +/- 10 meters N/A         Short/Crosstalk

                Pair B     89   +/- 10 meters N/A         Short/Crosstalk

                Pair C     81   +/- 10 meters N/A         Short/Crosstalk

                Pair D     81   +/- 10 meters N/A         Short/Crosstalk

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/10  auto  Pair A     68   +/- 10 meters N/A         Short/Crosstalk

                Pair B     69   +/- 10 meters N/A         Short/Crosstalk

                Pair C     62   +/- 10 meters N/A         Short/Crosstalk

                Pair D     62   +/- 10 meters N/A         Short/Crosstalk

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/12  auto  Pair A     37   +/- 10 meters N/A         Open

                Pair B     42   +/- 10 meters N/A         Short/Crosstalk

                Pair C     37   +/- 10 meters N/A         Short/Crosstalk

                Pair D     36   +/- 10 meters N/A         Short/Crosstalk

Interface Speed Local pair Pair length        Remote pair Pair status

--------- ----- ---------- ------------------ ----------- --------------------

Gi1/0/15  auto  Pair A     75   +/- 10 meters N/A         Open

                Pair B     83   +/- 10 meters N/A         Short/Crosstalk

                Pair C     72   +/- 10 meters N/A         Short/Crosstalk

                Pair D     72   +/- 10 meters N/A         Short/Crosstalk

Debug of ilpower controller

g  9 10:19:46.848 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:46.848 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:46.848 EDT: ***************************************

Aug  9 10:19:46.932 EDT: ILP Power apply to ( Gi1/0/4 ) Okay

Aug  9 10:19:46.932 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/4 ) Okay, pwr_used= 200200

Aug  9 10:19:46.941 EDT: ILP Power problem detected ( Gi1/0/4 )

Aug  9 10:19:46.941 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/4: Power given, but Power Controller does not report Power Good

Aug  9 10:19:46.941 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:46.941 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:46.941 EDT: ***************************************

Aug  9 10:19:47.243 EDT: ILP Power apply to ( Gi1/0/5 ) Okay

Aug  9 10:19:47.243 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/5 ) Okay, pwr_used= 184800

Aug  9 10:19:47.276 EDT: ILP Power problem detected ( Gi1/0/5 )

Aug  9 10:19:47.276 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/5: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.276 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:47.276 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.276 EDT: ***************************************

Aug  9 10:19:47.276 EDT: ILP State_Machine ( Gi1/0/2 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 10:19:47.276 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.276 EDT: ***************************************

Aug  9 10:19:47.276 EDT: ILP State_Machine ( Gi1/0/3 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 10:19:47.276 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.276 EDT: ***************************************

Aug  9 10:19:47.276 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:47.276 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.276 EDT: ***************************************

Aug  9 10:19:47.276 EDT: ILP State_Machine ( Gi1/0/6 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.276 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.276 EDT: ***************************************

Aug  9 10:19:47.343 EDT: ILP Power apply to ( Gi1/0/6 ) Okay

Aug  9 10:19:47.343 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/6 ) Okay, pwr_used= 169400

Aug  9 10:19:47.352 EDT: ILP Power problem detected ( Gi1/0/6 )

Aug  9 10:19:47.352 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/6: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.360 EDT: ILP State_Machine ( Gi1/0/9 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.360 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.360 EDT: ***************************************

Aug  9 10:19:47.469 EDT: ILP Power apply to ( Gi1/0/9 ) Okay

Aug  9 10:19:47.469 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/9 ) Okay, pwr_used= 154000

Aug  9 10:19:47.511 EDT: ILP Power problem detected ( Gi1/0/9 )

Aug  9 10:19:47.511 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/9: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.511 EDT: ILP State_Machine ( Gi1/0/6 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:47.511 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.511 EDT: ***************************************

Aug  9 10:19:47.511 EDT: ILP State_Machine ( Gi1/0/9 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:47.511 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.511 EDT: ***************************************

Aug  9 10:19:47.545 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.545 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.545 EDT: ***************************************

Aug  9 10:19:47.620 EDT: ILP Power apply to ( Gi1/0/1 ) Okay

Aug  9 10:19:47.620 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/1 ) Okay, pwr_used= 138600

Aug  9 10:19:47.629 EDT: ILP Power problem detected ( Gi1/0/1 )

Aug  9 10:19:47.629 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/1: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.629 EDT: ILP State_Machine ( Gi1/0/7 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.629 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.629 EDT: ***************************************

Aug  9 10:19:47.696 EDT: ILP Power apply to ( Gi1/0/7 ) Okay

Aug  9 10:19:47.696 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/7 ) Okay, pwr_used= 123200

Aug  9 10:19:47.704 EDT: ILP Power problem detected ( Gi1/0/7 )

Aug  9 10:19:47.712 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/7: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.712 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.712 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.712 EDT: ***************************************

Aug  9 10:19:47.821 EDT: ILP Power apply to ( Gi1/0/10 ) Okay

Aug  9 10:19:47.821 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/10 ) Okay, pwr_used= 107800

Aug  9 10:19:47.838 EDT: ILP Power problem detected ( Gi1/0/10 )

Aug  9 10:19:47.838 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/10: Power given, but Power Controller does not report Power Good

Aug  9 10:19:47.838 EDT: ILP State_Machine ( Gi1/0/11 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:19:47.838 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:47.838 EDT: ***************************************

Aug  9 10:19:47.998 EDT: ILP Power apply to ( Gi1/0/11 ) Okay

Aug  9 10:19:47.998 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/11 ) Okay, pwr_used= 92400

Aug  9 10:19:48.040 EDT: ILP Power problem detected ( Gi1/0/11 )

Aug  9 10:19:48.040 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/11: Power given, but Power Controller does not report Power Good

Aug  9 10:19:48.040 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:48.040 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.040 EDT: ***************************************

Aug  9 10:19:48.040 EDT: ILP State_Machine ( Gi1/0/7 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:48.040 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.040 EDT: ***************************************

Aug  9 10:19:48.040 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:48.040 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.040 EDT: ***************************************

E *****

Aug  9 10:20:20.040 EDT: ***************************************

Aug  9 10:20:20.040 EDT: %ILPOWER-7-DETECT: Interface Gi1/0/15: Power Device detected: IEEE PD

Aug  9 10:20:20.099 EDT: ILP Power apply to ( Gi1/0/15 ) Okay

Aug  9 10:20:20.099 EDT: ILP Power Accounting REQ_PWR ( Gi1/0/15 ) Okay sys_used=200200

Aug  9 10:20:20.107 EDT: ILP State_Machine ( Gi1/0/16 ): State= ILP_DETECTING_S, Event= IEEE_CLASS_DONE_EV

Aug  9 10:20:20.107 EDT: **** Instance 1 : Sub Address E *****

Aug  9 10:20:20.107 EDT: ***************************************

Aug  9 10:20:20.107 EDT: %ILPOWER-7-DETECT: Interface Gi1/0/16: Power Device detected: IEEE PD

Aug  9 10:20:20.158 EDT: ILP Power apply to ( Gi1/0/16 ) Okay

Aug  9 10:20:20.158 EDT: ILP Power Accounting REQ_PWR ( Gi1/0/16 ) Okay sys_used=215600

Aug  9 10:20:20.300 EDT: ILP State_Machine ( Gi1/0/17 ): State= ILP_DETECTING_S, Event= ILP_IEEE_DET_SHORT_EV

Aug  9 10:20:20.300 EDT: **** Instance 1 : Sub Address E *****

Aug  9 10:20:20.300 EDT: ***************************************

Aug  9 10:20:20.300 EDT: ILP State_Machine ( Gi1/0/18 ): State= ILP_DETECTING_S, Event= ILP_IEEE_DET_SHORT_EV

Aug  9 10:20:20.300 EDT: **** Instance 1 : Sub Address E *****

Aug  9 10:20:20.300 EDT: ***************************************

9:48.199 EDT: ILP Power problem detected ( Gi1/0/12 )

Aug  9 10:19:48.199 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/12: Power given, but Power Controller does not report Power Good

Aug  9 10:19:48.199 EDT: ILP State_Machine ( Gi1/0/8 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:48.199 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.199 EDT: ***************************************

Aug  9 10:19:48.207 EDT: ILP State_Machine ( Gi1/0/12 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:19:48.207 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.207 EDT: ***************************************

Aug  9 10:19:48.308 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 10:19:48.308 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:19:48.308 EDT: ***************************************

Aug  9 10:19:48.308 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

en, but Power Controller does not report Power Good

Aug  9 10:20:21.961 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:21.961 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:21.961 EDT: ***************************************

Aug  9 10:20:22.053 EDT: ILP Power apply to ( Gi1/0/4 ) Okay

Aug  9 10:20:22.053 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/4 ) Okay, pwr_used= 184800

Aug  9 10:20:22.053 EDT: ILP Power problem detected ( Gi1/0/4 )

Aug  9 10:20:22.053 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/4: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.053 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.053 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.053 EDT: ***************************************

Aug  9 10:20:22.129 EDT: ILP Power apply to ( Gi1/0/5 ) Okay

Aug  9 10:20:22.129 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/5 ) Okay, pwr_used= 169400

Aug  9 10:20:22.137 EDT: ILP Power problem detected ( Gi1/0/5 )

Aug  9 10:20:22.137 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/5: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.137 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.137 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.137 EDT: ***************************************

Aug  9 10:20:22.137 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.137 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.146 EDT: ***************************************

Aug  9 10:20:22.146 EDT: ILP State_Machine ( Gi1/0/6 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.146 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.146 EDT: ***************************************

Aug  9 10:20:22.204 EDT: ILP Power apply to ( Gi1/0/6 ) Okay

Aug  9 10:20:22.204 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/6 ) Okay, pwr_used= 154000

Aug  9 10:20:22.213 EDT: ILP Power problem detected ( Gi1/0/6 )

Aug  9 10:20:22.213 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/6: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.213 EDT: ILP State_Machine ( Gi1/0/7 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.213 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.213 EDT: ***************************************

Aug  9 10:20:22.330 EDT: ILP Power apply to ( Gi1/0/7 ) Okay

Aug  9 10:20:22.330 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/7 ) Okay, pwr_used= 138600

Aug  9 10:20:22.347 EDT: ILP Power problem detected ( Gi1/0/7 )

Aug  9 10:20:22.347 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/7: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.347 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.347 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.347 EDT: ***************************************

Aug  9 10:20:22.347 EDT: ILP State_Machine ( Gi1/0/6 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.347 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.347 EDT: ***************************************

Aug  9 10:20:22.347 EDT: ILP State_Machine ( Gi1/0/8 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.347 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.347 EDT: ***************************************

Aug  9 10:20:22.406 EDT: ILP Power apply to ( Gi1/0/8 ) Okay

Aug  9 10:20:22.406 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/8 ) Okay, pwr_used= 123200

Aug  9 10:20:22.422 EDT: ILP Power problem detected ( Gi1/0/8 )

Aug  9 10:20:22.422 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/8: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.422 EDT: ILP State_Machine ( Gi1/0/9 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.422 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.422 EDT: ***************************************

Aug  9 10:20:22.498 EDT: ILP Power apply to ( Gi1/0/9 ) Okay

Aug  9 10:20:22.498 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/9 ) Okay, pwr_used= 107800

Aug  9 10:20:22.506 EDT: ILP Power problem detected ( Gi1/0/9 )

Aug  9 10:20:22.506 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/9: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.506 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.506 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.506 EDT: ***************************************

Aug  9 10:20:22.582 EDT: ILP Power apply to ( Gi1/0/10 ) Okay

Aug  9 10:20:22.582 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/10 ) Okay, pwr_used= 92400

Aug  9 10:20:22.599 EDT: ILP Power problem detected ( Gi1/0/10 )

Aug  9 10:20:22.599 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/10: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.599 EDT: ILP State_Machine ( Gi1/0/11 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.599 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.599 EDT: ***************************************

Aug  9 10:20:22.649 EDT: ILP Power apply to ( Gi1/0/11 ) Okay

Aug  9 10:20:22.649 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/11 ) Okay, pwr_used= 77000

Aug  9 10:20:22.682 EDT: ILP Power problem detected ( Gi1/0/11 )

Aug  9 10:20:22.682 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/11: Power given, but Power Controller does not report Power Good

Aug  9 10:20:22.682 EDT: ILP State_Machine ( Gi1/0/7 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.682 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.682 EDT: ***************************************

Aug  9 10:20:22.682 EDT: ILP State_Machine ( Gi1/0/8 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.682 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.682 EDT: ***************************************

Aug  9 10:20:22.682 EDT: ILP State_Machine ( Gi1/0/9 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.682 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.691 EDT: ***************************************

Aug  9 10:20:22.691 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 10:20:22.691 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.691 EDT: ***************************************

Aug  9 10:20:22.691 EDT: ILP State_Machine ( Gi1/0/12 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 10:20:22.691 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 10:20:22.691 EDT:

Aug  9 11:05:52.693 EDT: %ILPOWER-7-DETECT: Interface Gi1/0/2: Power Device detected: IEEE PD

Aug  9 11:05:52.735 EDT: ILP Power apply to ( Gi1/0/2 ) Okay

Aug  9 11:05:52.735 EDT: ILP Power Accounting REQ_PWR ( Gi1/0/2 ) Okay sys_used=46200

Aug  9 11:05:52.861 EDT: ILP State_Machine ( Gi1/0/16 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 11:05:52.861 EDT: **** Instance 1 : Sub Address E *****

Aug  9 11:05:52.861 EDT: ***************************************

Aug  9 11:05:53.557 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 11:05:53.557 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:53.557 EDT: ***************************************

Aug  9 11:05:53.591 EDT: ILP Power apply to ( Gi1/0/10 ) Okay

Aug  9 11:05:53.591 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/10 ) Okay, pwr_used= 30800

Aug  9 11:05:53.599 EDT: ILP Power problem detected ( Gi1/0/10 )

Aug  9 11:05:53.599 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/10: Power given, but Power Controller does not report Power Good

Aug  9 11:05:53.599 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 11:05:53.599 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:53.599 EDT: ***************************************

Aug  9 11:05:54.966 EDT: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet5/0/44 (30), with CLINTON.MDF.01.cvs.k12.mi.us FastEthernet5/0/41 (102).

Aug  9 11:05:55.008 EDT: ILP State_Machine ( Gi1/0/10 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 11:05:55.008 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:55.008 EDT: ***************************************

Aug  9 11:05:55.034 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 11:05:55.034 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:55.034 EDT: ***************************************

Aug  9 11:05:55.075 EDT: ILP Power apply to ( Gi1/0/1 ) Okay

Aug  9 11:05:55.075 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/1 ) Okay, pwr_used= 15400

Aug  9 11:05:55.101 EDT: ILP Power problem detected ( Gi1/0/1 )

Aug  9 11:05:55.101 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/1: Power given, but Power Controller does not report Power Good

Aug  9 11:05:55.101 EDT: ILP State_Machine ( Gi1/0/2 ): State= ILP_PD_DETECTED_S, Event= ILP_IEEE_PGOOD_TIMEOUT_EV

Aug  9 11:05:55.101 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:55.101 EDT: ***************************************

Aug  9 11:05:55.176 EDT: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet5/0/41 (102), with CLINTON.MDF.01.cvs.k12.mi.us FastEthernet5/0/44 (30).

Aug  9 11:05:55.218 EDT: ILP Power apply to ( Gi1/0/2 ) Okay

Aug  9 11:05:55.218 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/2 ) Okay, pwr_used= 0

Aug  9 11:05:55.235 EDT: ILP Power problem detected ( Gi1/0/2 )

Aug  9 11:05:55.235 EDT: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/2: Power given, but Power Controller does not report Power Good

Aug  9 11:05:55.235 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 11:05:55.235 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:55.235 EDT: ***************************************

Aug  9 11:05:55.235 EDT: ILP State_Machine ( Gi1/0/2 ): State= ILP_BAD_POWER_S, Event= ILP_POWER_POLICE_DISABLE_EV

Aug  9 11:05:55.235 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:55.235 EDT: ***************************************

Aug  9 11:05:54.958 EDT: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet5/0/44 (30), with CLINTON.MDF.01.cvs.k12.mi.us FastEthernet5/0/41 (102). (CLINTON.MDF.01-5)

Aug  9 11:05:55.008 EDT: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet5/0/41 (102), with CLINTON.MDF.01.cvs.k12.mi.us FastEthernet5/0/44 (30). (CLINTON.MDF.01-5)

Aug  9 11:05:56.921 EDT: ILP State_Machine ( Gi1/0/1 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 11:05:56.921 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:56.921 EDT: ***************************************

Aug  9 11:05:56.921 EDT: ILP State_Machine ( Gi1/0/2 ): State= ILP_BAD_POWER_S, Event= PHY_CSCO_DETECTED_EV

Aug  9 11:05:56.921 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:56.921 EDT: ***************************************

Aug  9 11:05:58.179 EDT: ILP State_Machine ( Gi1/0/3 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.179 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.179 EDT: ***************************************

Aug  9 11:05:58.271 EDT: ILP Power apply to ( Gi1/0/3 ) Okay

Aug  9 11:05:58.271 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/3 ) Okay, pwr_used= 0

Aug  9 11:05:58.271 EDT: ILP Power apply to ( Gi1/0/3 ) Okay

Aug  9 11:05:58.271 EDT: ILP Start Power Controller phone detection ( Gi1/0/3 ) Okay

Aug  9 11:05:58.280 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/3 ) Okay

Aug  9 11:05:58.288 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.288 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.288 EDT: ***************************************

Aug  9 11:05:58.296 EDT: ILP Power apply to ( Gi1/0/4 ) Okay

Aug  9 11:05:58.296 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/4 ) Okay, pwr_used= 0

Aug  9 11:05:58.296 EDT: ILP Power apply to ( Gi1/0/4 ) Okay

Aug  9 11:05:58.296 EDT: ILP Start Power Controller phone detection ( Gi1/0/4 ) Okay

Aug  9 11:05:58.305 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/4 ) Okay

Aug  9 11:05:58.305 EDT: ILP State_Machine ( Gi1/0/5 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.305 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.305 EDT: ***************************************

Aug  9 11:05:58.347 EDT: ILP Power apply to ( Gi1/0/5 ) Okay

Aug  9 11:05:58.347 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/5 ) Okay, pwr_used= 0

Aug  9 11:05:58.347 EDT: ILP Power apply to ( Gi1/0/5 ) Okay

Aug  9 11:05:58.347 EDT: ILP Start Power Controller phone detection ( Gi1/0/5 ) Okay

Aug  9 11:05:58.347 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/5 ) Okay

Aug  9 11:05:58.389 EDT: ILP State_Machine ( Gi1/0/6 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.389 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.389 EDT: ***************************************

Aug  9 11:05:58.431 EDT: ILP Power apply to ( Gi1/0/6 ) Okay

Aug  9 11:05:58.431 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/6 ) Okay, pwr_used= 0

Aug  9 11:05:58.431 EDT: ILP Power apply to ( Gi1/0/6 ) Okay

Aug  9 11:05:58.431 EDT: ILP Start Power Controller phone detection ( Gi1/0/6 ) Okay

Aug  9 11:05:58.431 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/6 ) Okay

Aug  9 11:05:58.456 EDT: ILP State_Machine ( Gi1/0/11 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.456 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.456 EDT: ***************************************

Aug  9 11:05:58.498 EDT: ILP Power apply to ( Gi1/0/11 ) Okay

Aug  9 11:05:58.498 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/11 ) Okay, pwr_used= 0

Aug  9 11:05:58.498 EDT: ILP Power apply to ( Gi1/0/11 ) Okay

Aug  9 11:05:58.498 EDT: ILP Start Power Controller phone detection ( Gi1/0/11 ) Okay

Aug  9 11:05:58.498 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/11 ) Okay

Aug  9 11:05:58.582 EDT: ILP State_Machine ( Gi1/0/12 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.582 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.582 EDT: ***************************************

Aug  9 11:05:58.624 EDT: ILP Power apply to ( Gi1/0/12 ) Okay

Aug  9 11:05:58.624 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/12 ) Okay, pwr_used= 0

Aug  9 11:05:58.624 EDT: ILP Power apply to ( Gi1/0/12 ) Okay

Aug  9 11:05:58.624 EDT: ILP Start Power Controller phone detection ( Gi1/0/12 ) Okay

Aug  9 11:05:58.624 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/12 ) Okay

Aug  9 11:05:58.657 EDT: ILP State_Machine ( Gi1/0/7 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.657 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.657 EDT: ***************************************

Aug  9 11:05:58.733 EDT: ILP Power apply to ( Gi1/0/7 ) Okay

Aug  9 11:05:58.733 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/7 ) Okay, pwr_used= 0

Aug  9 11:05:58.733 EDT: ILP Power apply to ( Gi1/0/7 ) Okay

Aug  9 11:05:58.733 EDT: ILP Start Power Controller phone detection ( Gi1/0/7 ) Okay

Aug  9 11:05:58.733 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/7 ) Okay

Aug  9 11:05:58.741 EDT: ILP State_Machine ( Gi1/0/8 ): State= ILP_BAD_POWER_S, Event= BAD_PWR_TIMER_EV

Aug  9 11:05:58.741 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.741 EDT: ***************************************

Aug  9 11:05:58.800 EDT: ILP Power apply to ( Gi1/0/8 ) Okay

Aug  9 11:05:58.800 EDT: ILP Power Accounting RELEASE_PWR ( Gi1/0/8 ) Okay, pwr_used= 0

Aug  9 11:05:58.800 EDT: ILP Power apply to ( Gi1/0/8 ) Okay

Aug  9 11:05:58.800 EDT: ILP Start Power Controller phone detection ( Gi1/0/8 ) Okay

Aug  9 11:05:58.800 EDT: ILP Start PHY Cisco IP phone detection ( Gi1/0/8 ) Okay

Aug  9 11:05:58.808 EDT: ILP State_Machine ( Gi1/0/3 ): State= ILP_DETECTING_S, Event= IEEE_CLASS_DONE_EV

Aug  9 11:05:58.808 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.808 EDT: ***************************************

Aug  9 11:05:58.808 EDT: %ILPOWER-7-DETECT: Interface Gi1/0/3: Power Device detected: IEEE PD

Aug  9 11:05:58.850 EDT: ILP Power apply to ( Gi1/0/3 ) Okay

Aug  9 11:05:58.850 EDT: ILP Power Accounting REQ_PWR ( Gi1/0/3 ) Okay sys_used=15400

Aug  9 11:05:58.850 EDT: ILP State_Machine ( Gi1/0/4 ): State= ILP_DETECTING_S, Event= IEEE_CLASS_DONE_EV

Aug  9 11:05:58.850 EDT: **** Instance 0 : Sub Address 0 *****

Aug  9 11:05:58.850 EDT: ***************************************

Everyone's tags (6)
1 REPLY
Community Member

3750X phone power issues

ILPOWER-3-CONTROLLER_PORT_ERR  Controller port error, Interface x/y: Power Controller
reports power

Basically the cause of this Message is output in the following condition.

Imax error is reported by PoE controller of the switch, when a PoE PD device misbehaves
and draws more power ( Port Current ) beyond theirs specified limit.
Imax error is reported after the device is Powered up and it's an operating fault.
Usually that message can happen when new PD (power device) is connected and cause the
power spike on port, or PD is mis-behaving or there is a problem with cable or patch
panel.

Try the test below;

-- #test cable tdr inter 
-- Wait for approximately between 5 to 7 seconds.
-- #show cable tdr inter 

Length of the cable should be >50 ft

If this the test comes OK try the IP Phone in another siwtch and if it works fine,
at that poin tyou will need to contact TAC and request a replacement on the switch.

Regards,
4533
Views
0
Helpful
1
Replies
CreatePlease to create content