Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

3845 Switch Card

We have added a 4-port ethernet module to a customers 3845 switch. When he looks at the router to configure the card it only comes up as a layer 2 switch and cannot have any ip addresses added to it. Did we buy the wrong card or is there an IOS issue? The current IOS is

Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.3(14)T6, RELEASE SOFTWARE (fc2)

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: 3845 Switch Card

nshoe18 wrote:

We have added a 4-port ethernet module to a customers 3845 switch. When he looks at the router to configure the card it only comes up as a layer 2 switch and cannot have any ip addresses added to it. Did we buy the wrong card or is there an IOS issue? The current IOS is

Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.3(14)T6, RELEASE SOFTWARE (fc2)

You haven't actually said what card it is

However assuming it is a HWIC-4ESW then these are L2 switches only ie. you cannot configure the ports as L3 routed ports and assign IPs -

http://www.cisco.com/en/US/prod/collateral/routers/ps5853/prod_qas0900aecd8016c026_ps5854_Products_Q_and_A_Item.html

However you should be able to allocate the L2 ports into different vlans and create L3 vlan interfaces to route between them.

Jon

5 REPLIES
Hall of Fame Super Blue

Re: 3845 Switch Card

nshoe18 wrote:

We have added a 4-port ethernet module to a customers 3845 switch. When he looks at the router to configure the card it only comes up as a layer 2 switch and cannot have any ip addresses added to it. Did we buy the wrong card or is there an IOS issue? The current IOS is

Cisco IOS Software, 3800 Software (C3845-IPBASE-M), Version 12.3(14)T6, RELEASE SOFTWARE (fc2)

You haven't actually said what card it is

However assuming it is a HWIC-4ESW then these are L2 switches only ie. you cannot configure the ports as L3 routed ports and assign IPs -

http://www.cisco.com/en/US/prod/collateral/routers/ps5853/prod_qas0900aecd8016c026_ps5854_Products_Q_and_A_Item.html

However you should be able to allocate the L2 ports into different vlans and create L3 vlan interfaces to route between them.

Jon

New Member

Re: 3845 Switch Card

Are there any L3 switch modules for a 3845 router?  I cannot seem to find any.

Cisco Employee

Re: 3845 Switch Card

Purple

Re: 3845 Switch Card

  You can route with the hwic you just can't put a ip address directly on the interface as someone else said.   Create a layer 3 SVI (interface vlan X) and then put the interface into the correct vlan  "switchport access vlan X"  .  Also create the layer 2 vlan in the vlan database.

Silver

Re: 3845 Switch Card

i am asuming you bought a 4 port HWIC card and its purely layer 2 card and we cant assign an ip add ta an interface only thing you can do is create an SVI give it an ip add and assign the port to the respective SVI.

If you are planning to buy more cards try 1 port or 2 port HWIC they are only hwic that are layer 3 besides that NME module will fulfil your requirement.

Hope that helps

regards,

Varun

802
Views
0
Helpful
5
Replies