Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

6509 sup1A issue

Dear All,

I am testing the sup1A in my test bed with only chassis without any line modules. I am getting the following console errors.I have ios image and bootldr in the pc card (slot0:)

From sp Rommon after the cmd "BOOT=slot0:c6sup11.......... " it boots and terminated in RP Rommon with the error related to bootldr missing in bootflash of RP. Please help me how to copy the bootldr image in the pc card to the RP bootflash: also how to solve this above issue

The console message as below:

Fred > dir slot0:

File size Checksum File name

17661700 bytes (0x10d7f04) 0x56616541 c6sup11-jsv-mz.121-26.E3

1916864 bytes (0x1d3fc0) 0x7ae1ddef c6msfc-boot-mz.121-26.E3.bin

fred > dir bootflash:

File size Checksum File name

fred > set

config_gile=

config_file=

CONFIG_FILE=

SLOTCACHE=cards;

PNCL_2=2

PS1=fred >

boot=

BOOT=slot0:c6sup11-jsv-mz.121-26.E3

BOOTLDR=

BSI=0

PNCL_1=2

CRASHINFO=crashinfo_FAILED

RET_2_RTS=14:46:21 UTC Tue Oct 17 2006

RET_2_RCALTS=1161096382

?=0

fred > confreg 0x2102

You must reset or power cycle for new config to take effect

fred > reset

System Bootstrap, Version 5.3(2)

Copyright (c) 1994-2002 by cisco Systems, Inc.

c6k_sup1 processor with 65536 Kbytes of main memory

Autoboot executing command: "boot slot0:c6sup11-jsv-mz.121-26.E3"

Self decompressing the image : ################################################################################################################################################################################################################################################################################################################################################################################################################ [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) c6sup1_sp Software (c6sup1_sp-SPV-M), Version 12.1(26)E3, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Tue 16-Aug-05 00:25 by ccai

Image text-base: 0x60020F90, data-base: 0x60844000

00:00:03: %PFREDUN-6-ACTIVE: Initializing as ACTIVE processor

00:00:03: %OIR-6-CONSOLE: Changing console ownership to route processor

System Bootstrap, Version 12.0(3)XE, RELEASE SOFTWARE

Copyright (c) 1998 by cisco Systems, Inc.

Cat6k-MSFC platform with 131072 Kbytes of main memory

open failed due to full file table

loadprog: error - on file open

open: failed to find and/or load the bootloader: "slot0:c6msfc-boot-mz.121-26.E3.bin"

loadprog: error - on file open

open: failed to find and/or load the bootloader: "slot0:c6msfc-boot-mz.121-26.E3.bin"

loadprog: error - on file open

open: failed to find and/or load the bootloader: "slot0:c6msfc-boot-mz.121-26.E3.bin"

loadprog: error - on file open

open: failed to find and/or load the bootloader: "slot0:c6msfc-boot-mz.121-26.E3.bin"

26.E3.bin"

loadprog: error - on file open

open: failed to find and/or load the bootloader: "slot0:c6msfc-boot-mz.121-26.E3.bin"

loadprog: error - on file open

boot: cannot load "cisco2-Cat6k-MSFC"

System Bootstrap, Version 12.0(3)XE, RELEASE SOFTWARE

Copyright (c) 1998 by cisco Systems, Inc.

Cat6k-MSFC platform with 131072 Kbytes of main memory

boot: cannot determine first file name on device "bootflash:"

System Bootstrap, Version 12.0(3)XE, Incboot: cannot determine first file name on device "bootflash:"

thanks

swamy

11 REPLIES
Cisco Employee

Re: 6509 sup1A issue

Hi Swamy,

I belive you do not have boot image on your msfc bootflash.

If you don't, you need to have boot loader file at least in the MSFC bootflash to boot up. If this is the case, please xmodem the proper boot loader for MSFC first.

Once you have bootloader file either in bootflash or via xmodem, you should be able to boot up usingPCMCIA card.

Please beware that if you did xmodem, this doesn't actually copy to MSFC bootflash so

you would need to copy it later.

HTH

Ankur

New Member

Re: 6509 sup1A issue

Ankur,

Please tell me If after the xmodem copy,where the file will be? How can I copy it to the bootflash?

I confused about the xmodem destination location for the bootldr image.

Please help me

swamy

Cisco Employee

Re: 6509 sup1A issue

Hi Swamy,

After xmodem the image will be in DRAM of RP and it will just boot the RP and once it boots then you can tftp the boot loader image into bootflash of RP.

HTH

Ankur

* Pls rate all helpfull post

New Member

Re: 6509 sup1A issue

Ankur,

Bit confuse. If the bootldr in the RP DRAM then how can I tftp to the RP bootflash:

For Tftp to work the image should be in the local drive of the PC.

Please explain me.

I will rate soon.

swamy

New Member

Re: 6509 sup1A issue

Ankur,

In my pc card slot0: i have both IOS image and the bootldr image. I need to copy this bootldr to the RP bootflash:.

Please confirm me is it possible or as you said xmodem is the only solution. If xmodem only then please answer my reply to ur anohter message.

thanks

swamy

Cisco Employee

Re: 6509 sup1A issue

Hi Swamy,

You can first try copy from sup-slot0: and if that does not work then try xmodem.

Also you have 2 image so you only need to copy the bootloader image to the bootflash of RP.

Ankur

New Member

Re: 6509 sup1A issue

Dear,

I tried the sup-slot0 command with no auccess.so only left is xmodem

swamy

Cisco Employee

Re: 6509 sup1A issue

Hi Swamy,

From where do you tried or issued this command? You should be in RP rommon before issuing this command.

dir sup-slot0: will not work but copy command should work.

If you have already done this and still you cannot copy then xmodem the boo tloader when you are in RP rommon and once xmodem is complted it will copy the image into RP DRAM and RP DRAM will bot and once you see the RP boot prompt you can tftp the bot image into RP bootflash.

I hope I am bale to explain.

Ankur

New Member

Re: 6509 sup1A issue

Dear ankur,

Let me downlaod the image.

Thanks

swamy

New Member

Re: 6509 sup1A issue

Ankur,

Please correct me if i am wrong.

BOOTLDR=bootflash:c6msfc-boot-mz.121-26.E3.bin

Should the .bin be there or not.

Thanks

swamy

Cisco Employee

Re: 6509 sup1A issue

Hi Swamy,

No worry. So now your bootloader is into bootflash? Were you able to xmodem successfully or copy commadn worked?

Regards,

Ankur

804
Views
0
Helpful
11
Replies
CreatePlease to create content