Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

6509 Sup720 PFC 3B question

My question is, i am applying service policy on vlan interface for output, it gives me this error.

priority command is not supported in output direction for this interface

Configuration failed

Here is the configuration i am using

class-map match-any Signal

match access-group 103

class-map match-any Voice

match protocol rtp audio

!

!

policy-map ProtectVoice

class Voice

set ip dscp 46

priority percent 70

class Signal

bandwidth percent 5

set ip dscp 24

!

IOS Version - 12.2(18)SXF11

Please let me know if anyone has gone through this and if any resolution.

Thanks,

5 REPLIES
Hall of Fame Super Bronze

Re: 6509 Sup720 PFC 3B question

Please post the output from typing

show queueing interface [interface_where_policy_is_being_applied] | include type command.

__

Edison.

New Member

Re: 6509 Sup720 PFC 3B question

Hello Edison,

Thanks for your reply. Here is the output of queue command,

sh queueing interface vlan 200

Interface Vlan200 queueing strategy: none

Thanks,

Yogesh

Hall of Fame Super Bronze

Re: 6509 Sup720 PFC 3B question

That's the logical interface, I need to know the output from the physical interface.

Better, yet - post the output from typing show module and tell us what linecard is the one used on this policy.

In short, not all modules support priority queueing in egress, I need to find out if you have such module.

__

Edison.

New Member

Re: 6509 Sup720 PFC 3B question

sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1033YLHB

2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1033YLME

3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL1133XMYK

4 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1033YLNL

5 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL11402PEH

7 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL1033YLEB

8 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-TX SAL11434RQ7

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0018.ba3c.6780 to 0018.ba3c.67af 11.0 7.2(1) 8.7(0.22)BUB Ok

2 0018.ba3c.6af0 to 0018.ba3c.6b1f 11.0 7.2(1) 8.7(0.22)BUB Ok

3 001c.58d3.aa80 to 001c.58d3.aa8f 4.6 7.2(1) 8.7(0.22)BUB Ok

4 0018.ba3c.6df0 to 0018.ba3c.6e1f 11.0 7.2(1) 8.7(0.22)BUB Ok

5 0016.c85e.e2a8 to 0016.c85e.e2ab 5.4 8.4(2) 12.2(33)SXH1 Ok

7 0018.ba3c.5b30 to 0018.ba3c.5b5f 11.0 7.2(1) 8.7(0.22)BUB Ok

8 001d.a25f.1ff8 to 001d.a25f.2027 11.3 7.2(1) 8.7(0.22)BUB Ok

Mod Sub-Module Model Serial Hw Status

---- --------------------------- ------------------ ----------- ------- -------

5 Policy Feature Card 3 WS-F6K-PFC3B SAL11402TSC 2.3 Ok

5 MSFC3 Daughterboard WS-SUP720 SAL11392CPV 3.0 Ok

Mod Online Diag Status

---- -------------------

1 Pass

2 Pass

3 Pass

4 Pass

5 Pass

7 Pass

8 Pass

Hall of Fame Super Bronze

Re: 6509 Sup720 PFC 3B question

Ok, those modules support priority queueing

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd8017376e.html

Configuration on priority queueing for PFC 3B can be found at:

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/configuration/guide/qos.html#wp1750910

Keep in mind, QoS on Cat6k is not the same as regular IOS routers while the commands are available on both platforms. To understand QoS in Cat6k I usually find this article quite helpful:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/prod_white_paper0900aecd803e5269.html

HTH,

__

Edison.

298
Views
0
Helpful
5
Replies