04-17-2012 06:41 AM - edited 03-07-2019 06:10 AM
Hello Guys, i have one of my switch modules that shows PwrDown when i issue the command show mod.
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
2 48 48 port 10/100/1000mb EtherModule WS-X6148-GE-TX SAL1029VWZ5
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL104681AW
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 0011.5ce1.8e64 to 0011.5ce1.8e6f 4.1 12.2(18r)SX2 12.2(33)SXI2 Ok
2 000a.b843.ca10 to 000a.b843.ca3f 7.0 7.2(1) 12.2(33)SXI2 Ok
3 0019.aa98.90c8 to 0019.aa98.90d7 4.5 7.2(1) 12.2(33)SXI2
PwrDown
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Policy Feature Card 3 WS-F6K-PFC3B SAD091601CM 2.1 Ok
1 Cat6k MSFC 2A daughterboard WS-F6K-MSFC2A SAD091504C1 3.0 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Not Applicable
i tried disabling the diagnostic monitor for the module, did a power enable module command and then reset it but it still fails.
this is the third blade that i am replacing in a few weeks and i still get the same error. i am persuded that it is not a hardware since it is the third blade in a matter of weeks.
after the module reset, i receive this error % module 3 is operationally off (FRU-power failed)
could an ios upgrade solve this issue? are there any ios related bugs?
thanks for the help.
Solved! Go to Solution.
04-18-2012 03:35 AM
Apr 18 08:13:08.046 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure.
I think you should open a TAC Case. You've got a hardware failure with the line card. Please include the "sh log" that you've posted with the TAC Case.
04-17-2012 07:38 AM
Hi,
If you are having problem with multiple blades in the same slot, take a flash light have a look at the pins in the back of the chassis and make sure the pins on the backplane are not bend. You are running a very old IOS (SXI2). If I remember correctly, this version was differed, so it is a good idea to load a newer version, but I don't think that is your issue.
HTH
04-17-2012 09:31 AM
Seeing you have 6 open slots have you tried any slot besides 3 ? If you run it in one of the other slots and its ok then you know it is an issue in the chassis slot .
04-17-2012 03:05 PM
1 9 Supervisor Engine 32 8GE (Active) WS-SUP32-GE-3B SAD09120263
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516A-GBIC SAL104681AW
Correct me if I'm wrong here, but I believe the 6516 line card is NOT COMPATIBLE with the Sup32.
04-17-2012 06:34 PM
04-17-2012 07:05 PM
Oh cool! Thanks Glen.
04-17-2012 07:06 PM
Now that Glen has shown me that the module works with Sup32, can I ask if you console to the chassis, reseat the blade and post the entire bootup process of this line card?
04-18-2012 02:49 AM
Hello all and thanks for you helpful post.
@leolaohoo, the output is below. when the slot is placed in another chassis, it work. so it is more likely a defected backplane. all the pins seem normal
Apr 18 08:13:05.491 CET: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
Apr 18 08:13:08.046 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x0, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x1, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Apr 18 08:13:08.046 CET: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed)
Apr 18 08:13:35.373 CET: %DIAG-SP-6-RUN_MINIMUM: Module 3: Running Minimal Diagnostics...
Apr 18 08:13:38.469 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x0, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x1, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Apr 18 08:13:38.469 CET: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed)
Apr 18 08:14:04.627 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x0, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x1, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Apr 18 08:14:04.627 CET: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed)
Apr 18 08:14:31.084 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x0, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x1, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Apr 18 08:14:31.084 CET: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed)
Apr 18 08:14:57.223 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure. PMB registers are dumped as follows, R0= 0x0, R1= 0x2, R2= 0x0, R3= 0x0, R4= 0x0, R5= 0x1, R6= 0x0, R7= 0x1, R8= 0x0, R9= 0x0, R10= 0x0, R11= 0x0, R12= 0x0, R13= 0x0, R14= 0x0, R15= 0x0
Apr 18 08:14:57.223 CET: %C6KPWR-SP-4-DISABLED: power to module in slot 3 set off (FRU-power failed)
i think i should open a TAC case.
04-18-2012 03:35 AM
Apr 18 08:13:08.046 CET: %OIR-SP-6-PWRFAILURE: Module 3 is being disabled due to power convertor failure.
I think you should open a TAC Case. You've got a hardware failure with the line card. Please include the "sh log" that you've posted with the TAC Case.
04-18-2012 05:09 AM
thanks for your help !
04-18-2012 03:33 PM
Thanks for the ratings.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: