11-28-2013 03:41 AM - edited 03-07-2019 04:49 PM
Hi,
after upgrading to 2t supervisor our wism controller is not working properly.
I can connect to it via service ip address but via management I can't.
status is ok, on line diagnostic is ok... but all AP are not working.
on 6509 we are runing
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
on wism:
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.240.0
RTOS Version..................................... 7.0.240.0
Bootloader Version............................... 7.0.240.0
Emergency Image Version.......................... 7.0.240.0
Build Type....................................... DATA + WPS
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 16 CEF720 16 port 10GE WS-X6716-10GE
2 6 Firewall Module WS-SVC-FWM-1
3 10 WiSM WLAN Service Module WS-SVC-WISM-1-K9
5 5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
1 f866.f220.08 to f86.f220.07 1.0 12.2(18r)S1 15.1(2)SY Ok
2 0023.3d.e174 to 00.334d.e17b 4.5 7.2(1) 4.1(9) Ok
3 0025.87.d73a to 025.84.d749 2.3 12.2(14r)S5 15.1(2)SY Ok
5 5057.a8.1d to 505a8.1d18 1.5 12.2(50r)SYS 15.1(2)SY Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
1 Distributed Forwarding Card WS-F6K-DFC4-E 1.2 Ok
3 Centralized Forwarding Card WS-SVC-WISM-1-K9-D 2.1 Ok
5 Policy Feature Card 4 VS-F6K-PFC4 2.1 Ok
5 CPU Daughterboard VS-F6K-MSFC5 2.1 Ok
Mod Online Diag Status
---- -------------------
1 Pass
2 Pass
3 Pass
5 Pass
is there problem with ios incapability or am I doing something wrong.
regards,
Ivan
Solved! Go to Solution.
11-28-2013 03:07 PM
Check your allowed VLAN is enabled on the WiSM1 port channel.
11-28-2013 08:47 AM
Hi,
Your IOS is good, as you have a later version than what is required which is 15.0(1)SY.
what is the output of "sh wism status"?
Have you tried rebooting the switch?
HTH
11-28-2013 03:07 PM
Check your allowed VLAN is enabled on the WiSM1 port channel.
11-29-2013 01:47 AM
Ok i think the problem is in:
Port-channel1 unassigned YES unset down down
Port-channel2 unassigned YES unset down down
WiSM Controller 2 in Slot 3 not configured
Operational Status of the Controller : Oper-Up
Service VLAN : 702
Service Port : 10
Service Port Mac Address : 0023.eb01.c322
Service IP Address : 10.7.2.12
Management IP Address : 10.7.3.20
Software Version : 7.0.240.0
Port Channel Number : 0
WCP Keep Alive Missed : 0
i just need to figure this out :-))
Thx.
11-29-2013 01:59 AM
hi!
find solution:
wism module X controller Y allowed-vlan A,B,C
THX everyone for help!
11-29-2013 02:46 AM
Can you please mark this thread as "Answered"?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: