cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
627
Views
0
Helpful
5
Replies

6509 upgrade sup 720 to 2t - wism1 not working

Ivan Marinovic
Level 1
Level 1

Hi,

after upgrading to 2t supervisor our wism controller is not working properly.

I can connect to it via service ip address but via management I can't.

status is ok, on line diagnostic is ok... but all AP are not working.

on 6509 we are runing

bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin

on wism:

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.240.0

RTOS Version..................................... 7.0.240.0

Bootloader Version............................... 7.0.240.0

Emergency Image Version.......................... 7.0.240.0

Build Type....................................... DATA + WPS

Mod Ports Card Type                              Model              Serial No.

--- ----- -------------------------------------- ------------------ -----------

  1   16  CEF720 16 port 10GE                    WS-X6716-10GE     

  2    6  Firewall Module                        WS-SVC-FWM-1      

  3   10  WiSM WLAN Service Module               WS-SVC-WISM-1-K9  

  5    5  Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G      

Mod MAC addresses                       Hw    Fw           Sw           Status

--- ---------------------------------- ------ ------------ ------------ -------

  1  f866.f220.08 to f86.f220.07   1.0   12.2(18r)S1  15.1(2)SY    Ok

  2  0023.3d.e174 to 00.334d.e17b   4.5   7.2(1)       4.1(9)       Ok

  3  0025.87.d73a to 025.84.d749   2.3   12.2(14r)S5  15.1(2)SY    Ok

  5  5057.a8.1d to 505a8.1d18   1.5   12.2(50r)SYS 15.1(2)SY    Ok

Mod  Sub-Module                  Model              Serial       Hw     Status

---- --------------------------- ------------------ ----------- ------- -------

  1  Distributed Forwarding Card WS-F6K-DFC4-E        1.2    Ok

  3  Centralized Forwarding Card WS-SVC-WISM-1-K9-D   2.1    Ok

  5  Policy Feature Card 4       VS-F6K-PFC4          2.1    Ok

  5  CPU Daughterboard           VS-F6K-MSFC5         2.1    Ok

Mod  Online Diag Status

---- -------------------

  1  Pass

  2  Pass

  3  Pass

  5  Pass

is there problem with ios incapability or am I doing something wrong.

regards,

Ivan

1 Accepted Solution

Accepted Solutions

Leo Laohoo
Hall of Fame
Hall of Fame

Check your allowed VLAN is enabled on the WiSM1 port channel. 

View solution in original post

5 Replies 5

Reza Sharifi
Hall of Fame
Hall of Fame

Hi,

Your IOS is good, as you have a later version than what is required which is 15.0(1)SY.

what is the output of "sh wism status"?

Have you tried rebooting the switch?

HTH

Leo Laohoo
Hall of Fame
Hall of Fame

Check your allowed VLAN is enabled on the WiSM1 port channel. 

Ivan Marinovic
Level 1
Level 1

Ok i think the problem is in:

Port-channel1          unassigned      YES unset  down                  down   

Port-channel2          unassigned      YES unset  down                  down   

WiSM Controller 2 in Slot 3 not configured

Operational Status of the Controller : Oper-Up

Service VLAN                         : 702

Service Port                         : 10

Service Port Mac Address             : 0023.eb01.c322

Service IP Address                   : 10.7.2.12

Management IP Address                : 10.7.3.20

Software Version                     : 7.0.240.0

Port Channel Number                  : 0

WCP Keep Alive Missed                : 0

i just need to figure this out :-))

Thx.

Ivan Marinovic
Level 1
Level 1

hi!

find solution:

wism module X controller Y allowed-vlan A,B,C

THX everyone for help!

Can you please mark this thread as "Answered"?

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: