Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

6513 modules not detected ( urgent )

Dear all

I have cisco 6513 switch ( IOS Version 12.2(17d)SXB9 ).i have one ethernet modules installed . i can see this module from CatOS , but i am unable to see ethernet module when i login into MSFC

Router#sh version

Cisco Internetwork Operating System Software

IOS (tm) MSFC2A Software (C6MSFC2A-JK9SV-M), Version 12.2(17d)SXB9, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Thu 21-Jul-05 03:42 by pwade

Image text-base: 0x40008FBC, data-base: 0x425D8000

ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)

BOOTLDR: MSFC2A Software (C6MSFC2A-JK9SV-M), Version 12.2(17d)SXB9, RELEASE SOFTWARE (fc2)

Router uptime is 1 minute

System returned to ROM by power-on

System image file is "bootflash:c6msfc2a-jk9sv-mz.122-17d.SXB9.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco MSFC2A (R7000) processor (revision MSFC2A) with 458752K/65536K bytes of memory.

Processor board ID MSFC2A

R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache

Last reset from power-on

Bridging software.

X.25 software, Version 3.0.0.

SuperLAT software (copyright 1990 by Meridian Technology Corp).

TN3270 Emulation software.

509K bytes of non-volatile configuration memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

Configuration register is 0x2102

show version , sh run-config unable to show any ethernet module , nor i can see any interface commands related to gigbitethernet

how i can deletect ethernet module in MSFC .

Regards

1 ACCEPTED SOLUTION

Accepted Solutions
Cisco Employee

Re: 6513 modules not detected ( urgent )

Hi Kernel,

Yes you can run your switch in NATIVE IOS mode but currently your switch is running in Hybrid mode and to convert form Hybrid mode to Native mode you have to go through the conversion procedure.

Have a look at this link for more details on Hrbrid mode to Native Mode conversion

http://www.cisco.com/warp/public/473/81.html#conv_msfc_2

HTH

Ankur

*Pls rate all helpfull post

3 REPLIES
Cisco Employee

Re: 6513 modules not detected ( urgent )

Hi Kernel,

You are not running a Native IOS on your box and your sup engine is running in HYBRID MODE where there is a CATOS for all layer 2 configuration and interfaces configuration and IOS loaded on MSFC for all routing configuration.

In HYBRID mode you can see all modules only from CATOS and when you access MSFC via session command you are on the IOS on MSFC which can be used to configure all layer 3 coniguration like intervlan routing and other stuffs.

Only when you are running a NATIVE IOS which means a complete one IOS for both supervisor and msfc then from IOS mode you can see all your modules installed and can configure the ethernet interfaces even as layer 3 interfaces which is not possible in HYBRID mode.

So you won;t be able to see any modules from MSFC itself. So you can configure your ethernet module and its interfaces only for layer 2 operation from CATOS and all configurations relating to layer 3 for those vlans should be done on MSFC.

HTH

Ankur

*Pls rate helpfull post

New Member

Re: 6513 modules not detected ( urgent )

Thanks a lot for your reply

Can i run the my switch into native IOS mode

Regards

K

Cisco Employee

Re: 6513 modules not detected ( urgent )

Hi Kernel,

Yes you can run your switch in NATIVE IOS mode but currently your switch is running in Hybrid mode and to convert form Hybrid mode to Native mode you have to go through the conversion procedure.

Have a look at this link for more details on Hrbrid mode to Native Mode conversion

http://www.cisco.com/warp/public/473/81.html#conv_msfc_2

HTH

Ankur

*Pls rate all helpfull post

136
Views
0
Helpful
3
Replies
CreatePlease to create content