Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

802.1q trunking on ethernet

Hi

Can someone please confirm that it is not possible to configure 802.1q trunking on an ethernet interface. I'm busy with a lab setup and the router (a 3620) will not accept the encapsulation dot1q x (where x is the vlan number). I'm running IOS12.3 IP plus.

Thanks,

9 REPLIES

Re: 802.1q trunking on ethernet

Hi

Can you post the output of show version here ?

regds

New Member

Re: 802.1q trunking on ethernet

Thanks for the quick response. Please see the output below.

Cisco Internetwork Operating System Software

IOS (tm) 3600 Software (C3620-I-M), Version 12.2(31), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by cisco Systems, Inc.

Compiled Thu 11-Aug-05 14:30 by tinhuang

Image text-base: 0x60008930, data-base: 0x60A3E000

ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)

ROM: 3600 Software (C3620-I-M), Version 12.2(31), RELEASE SOFTWARE (fc2)

R6 uptime is 1 hour, 50 minutes

System returned to ROM by power-on

System image file is "flash:c3620-i-mz.122-31.bin"

cisco 3620 (R4700) processor (revision 0x81) with 28672K/4096K bytes of memory.

Processor board ID 08359841

R4700 CPU at 80Mhz, Implementation 33, Rev 1.0

Bridging software.

X.25 software, Version 3.0.0.

2 Ethernet/IEEE 802.3 interface(s)

2 Serial network interface(s)

DRAM configuration is 32 bits wide with parity disabled.

29K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x2101

Regards, EP

Re: 802.1q trunking on ethernet

Hi EP

The code you currently have in your box belongs to 12.2 Release and of IP Feature set.

You need to have IP PLUS feature set to have the required config in place.

you can make use of the below mentioned tool to find out the ip plus image which can fit into your current flash/dram available in place..

http://tools.cisco.com/Support/Fusion/FusionHome.do

regds

New Member

Re: 802.1q trunking on ethernet

Hi Spremkumar

Could you just confirm something for me please? Do you know if this command is supported on a normal ethernet interface as apposed to a fastethernet interface. Meanwhile I'll check the memory req.

Another thing is.. I thought the MZ in the following image name indicates that this is a IP Plus image. I'm getting a bit rusty on the versions.

Thanks, EP

Re: 802.1q trunking on ethernet

Hi EP

Though i haven't tried configuring IEEE 802.1q trunking on an Normal Ethernet interface i doubt on the support of the same with ethernet interfaces.

The config samples too are pointing me towards fast ethernet interfaces..

Also do refer this link..

http://www.cisco.com/univercd/cc/td/doc/product/access/mar_3200/mar_conf/m511m80.htm

regds

New Member

Re: 802.1q trunking on ethernet

Hi

I've just upgraded to IP Plus version. The answer is yes, you can configure Dot1q using the encapsulation command under the subinterface using a normal ethernet interface as apposed to a fastethernet interface.

Thanks to everyone for your help.

EP

Re: 802.1q trunking on ethernet

Hi EP

Good that you got your issue resolved and posted back ..

cheers..

Re: 802.1q trunking on ethernet

Hi,

You should be able to do 802.1q tagging over the ethernet interface.

What is the error message that you are getting while doing so.?

Before creating the sub-interfaces, you should remove any ip address configuration done on the physical interface.

Can you post your config ?

-VJ

-VJ

Re: 802.1q trunking on ethernet

Hi,

Oops. Just noticed the update from another netpro user.

Kindly ignore my previous update.

-VJ

326
Views
4
Helpful
9
Replies