Cisco Support Community
Community Member

ADSL Config

Hi All,

I have 2811 router with HIW-1ADSL card, i need to configure this router for internet connection. I have already one ADSL Linksys router up and running the configuration of that Linksys router as follows

Encapsulation : RFC 2516 PPPOE

pcr rate :cps

scr rate :cps

virtual circuit: vpi=0


DSL Modulation : Multimode

PPPOE setting:

username : John

password : XXXX

connect on Demand : yes

Max idle timeo out : 5 mints

can you help to do the same configuration in above said cisco 2811 router.


Hall of Fame Super Silver

Re: ADSL Config

Hello Jagan,

for releases after IOS 12.2(13)T the following is enough:

suppose that atm0/0 is the name of the DSL interface on your router

interface ATM0/0

no ip address

no ip mroute-cache

no atm ilmi-keepalive

dsl operating-mode auto

pvc 0/50

enc aal5snap

pppoe-client dial-pool-number 2


interface Dialer2

description PPPoEoverATM

mtu 1492

ip address negotiated

encapsulation ppp

dialer pool 2

dialer-group 2

dialer idle-timeout 300

ppp chap hostname John

ppp chap password XXXX

ppp pap sent-username John password XXXX


dialer-list 2 protocol ip permit

ip route dialer2 200

you need also to NAT the internal interface to allow internet access from inside.

int fas0/0

ip address

ip nat inside

access-list 11 permit

int dialer2

ip nat outside

ip nat inside source list 11 int dialer2 overload


Hope to help


Community Member

Re: ADSL Config

Thanks a lot brother. Will let you know the satus.

Community Member

Re: ADSL Config

Hi Giuseppe,

I have configured ADSL router im getting ip address to my outside interface and atm interface is showing up. But i can't able to access internet. When i issued "debug atm error"

i got following message.

*Sep 17 11:18:15.415: dslsar_ng_transmit_pak_wrapper: deq(474FE2D4). ATM vcd=1 Transmit VCD=1

*Sep 17 11:18:15.415: dslsar_ng_transmit_pak_wrapper : encap = Data

*Sep 17 11:18:25.655: dslsar_ng_transmit_pak_wrapper: deq(46DEC6E8). ATM vcd=1 Transmit VCD=1

*Sep 17 11:18:25.655: dslsar_ng_transmit_pak_wrapper : encap = Data

*Sep 17 11:18:31.535: dslsar_ng_transmit_pak_wrapper: deq(46DED204). ATM vcd=1 Transmit VCD=1

*Sep 17 11:18:31.535: dslsar_ng_transmit_pak_wrapper : encap = Data

*Sep 17 11:18:35.895: dslsar_ng_transmit_pak_wrapper: deq(46DEE83C). ATM vcd=1 Transmit VCD=1

*Sep 17 11:18:35.895: dslsar_ng_transmit_pak_wrapper : encap = Data

*Sep 17 11:19:47.575: dslsar_ng_transmit_pak_wrapper: deq(474FEDF0). ATM vcd=1 Transmit VCD=1

*Sep 17 11:19:47.575: dslsar_ng_transmit_pak_wrapper : encap = Data

*Sep 17 11:19:57.815: dslsar_ng_transmit_pak_wrapper: deq(46DEFAC0). ATM vcd=1 Transmit VCD=1

*Sep 17 11:19:57.815: dslsar_ng_transmit_pak_wrapper : en ip virtual-reassembly

kindly assist me on this issue.



Community Member

Re: ADSL Config

Hi Giuseppe,

This issue is resolved it an ppp authentication issue.

Thanks a lot in assisting me on this issue.



CreatePlease to create content