Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Aironet 702 - configuration issue

hi,

  I bought new Cisco Aironet 702. I have problem with configuration. I can't access to configure terminal option or to web setup. Below is startup screens from Aironet. There are few errors during startup process:

no ip http server

       ^

% Invalid input detected at '^' marker.

%Error opening flash:/ap1g1-rcvk9w8-mx/info (No such file or  directory)cisco AIR-CAP702I-E-K9 (MIPS74k) processor (revision 01) with  73728K/57344K bytes of memory.

I accessed to exec mode using default login and password but I couldn't access to configure terminal options. Why Cisco doesn't recognize this command?

AP5006.04a6.231e#conf te

                  ^

% Invalid input detected at '^' marker.

startup process:

flash size 1MB, sector count = 64

Flash:  1 MB

Fetching MAC Address from 0x87fe3908

eth0: 50:06:04:a6:23:1e

ATHRSF1_PHY: Port 4, Negotiation timeout

Ethernet link down

eth0

Ether initialization ok!

Atheros on-chip NAND FLash Controller Driver, Version 0.1 (c) 2010 Atheros Communications, Ltd.

Ath Nand ID[87ff117c]: 2c:f1:80:95:02

ONFI MICRON      MT29F1G08ABADAWP

Micron NAND 128MiB 3,3V 8-bit [128MB]

====== NAND Parameters ======

sc = 0x87ff1158 bbt = 0x87f98360 bbt_size = 0x100 nf_ctrl = 0x344

page = 0x800 block = 0x20000 oob = 0x40

size = 128MB

Setting 0xb8116290 to 0x2a542d0f

Test Size=0x8000000, Start!!

RAM test complete!

PTD Init

MAC address check ok!

boot method:3

Hit "ESC" to stop autoboot:  0

Uncompressed size: 319299 = 0x4DF43

Loading .text @ 0x84000000 (205088 bytes)

Loading .rodata @ 0x84032120 (38400 bytes)

Loading .data @ 0x8403b720 (3200 bytes)

Loading .data.rel.local @ 0x8403c3a0 (992 bytes)

Loading .data.rel @ 0x8403c780 (124 bytes)

Loading .data.rel.ro.local @ 0x8403c7fc (92 bytes)

Loading .data.rel.ro @ 0x8403c858 (960 bytes)

Clearing .bss @ 0x8403cc20 (161112 bytes)

Clearing .scommon @ 0x84064178 (60 bytes)

## Starting application at 0x84000000 ...

IOS Secondary Bootloader - Starting system.

Ath Nand ID: 95:80:f1:2c:00

Using driver version 1 for media type 2

Valid buffers 120

total120  120

success found all blocks

start end 65 72

found in range

high low end 2335 2089 72

Xmodem file system is available.

mifs[0]: 10 files, 2 directories

mifs[0]: Total bytes     :  131334144

mifs[0]: Bytes used      :    7591936

mifs[0]: Bytes available :  123742208

mifs[0]: mifs fsck took 0 seconds.

Base Ethernet MAC address: 50:06:04:a6:23:1e

Setup MAC....

Waiting for PHY auto negotiation to complete...Port 4 Negogiation timeout.

Ethernet link is down.

Setting Drop CRC Errors, Pause Frames and Length Error frames

: cfg1 0x7 cfg2 0x7114

Loading "flash:/ap1g1-rcvk9w8-mx.152-4.JA/ap1g1-rcvk9w8-mx.152-4.JA"...############################################################################################################################################################################################################################################################################################################################################################

File "flash:/ap1g1-rcvk9w8-mx.152-4.JA/ap1g1-rcvk9w8-mx.152-4.JA" uncompressed and installed, entry point: 0x60080000

executing...

Stop MAC.

AP1G1 Starting...

cp0 timer begin value is set as 1000

prid= 1974C

Starts main.

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco IOS Software, ap1g1 Software (ap1g1-RCVK9W8-M), Version 15.2(4)JA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 18-Jun-13 14:15 by prod_rel_team

Initializing flashfs...

Ath Nand ID: 95:80:F1:2C:00

Using driver version 1 for media type 2

Valid buffers 120

total120  120

success found all blocks

start end 65 72

found in range

high low end 2335 2089 72

mifs[3]: 10 files, 2 directories

mifs[3]: Total bytes     : 131334144

mifs[3]: Bytes used      : 7591936

mifs[3]: Bytes available : 123742208

mifs[3]: mifs fsck took 2 seconds.

mifs[3]: Initialization complete.

...done Initializing flashfs.

Base Ethernet MAC address: 50:06:04:A6:23:1E

Waiting for PHY auto negotiation to complete...Port 4 Negogiation timeout.

This product contains cryptographic features and is subject to United

no ip http server

       ^

% Invalid input detected at '^' marker.

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

%Error opening flash:/ap1g1-rcvk9w8-mx/info (No such file or directory)cisco AIR-CAP702I-E-K9 (MIPS74k) processor (revision 01) with 73728K/57344K bytes of memory.

Processor board ID KWC1717004X

MIPS74k CPU at 40Mhz, revision number 0x0000

Last reset from power-on

LWAPP image version 7.5.1.33

1 Gigabit Ethernet interface

32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 50:06:04:A6:23:1E

Part Number                          : 74-11077-01

PCA Assembly Number                  : 000-00000-00

PCA Revision Number                  :

PCB Serial Number                    : KWC1717004X

Top Assembly Part Number             : 000-00000-00

Top Assembly Serial Number           : KWC1717004X

Top Revision Number                  : 01

Product/Model Number                 : AIR-CAP702I-E-K9

% Please define a domain-name first.

logging facility kern

        ^

% Invalid input detected at '^' marker.

logging trap emergencies

        ^

% Invalid input detected at '^' marker.

Press RETURN to get started!

: Mac unit                :   0

: Max segments per packet :   1

: Max tx descriptor count :   128

: Max rx descriptor count :   256

: Mac capability flags    :   4400

athr_gmac_hw_setup mac: 0x61953F40

Setting Drop CRC Errors, Pause Frames and Length Error frames

: cfg1 0x7 cfg2 0x7114

*Mar  1 00:00:13.683: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Mar  1 00:00:13.895: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up

*Mar  1 00:00:16.711: %SYS-5-RESTART: System restarted --

Cisco IOS Software, ap1g1 Software (ap1g1-RCVK9W8-M), Version 15.2(4)JA, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 18-Jun-13 14:15 by prod_rel_team

*Mar  1 00:00:16.731: *** not invoke

*Mar  1 00:00:16.751: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Mar  1 00:00:16.755: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config

*Mar  1 00:00:16.767: %PARSER-4-BADCFG: Unexpected end of configuration file.

lwapp_crypto_init: MIC Present and Parsed Successfully

*Mar  1 00:00:17.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up

User Access Verification

Username: Cisco

no bridge-group 1 source-learning

                   ^

% Invalid input detected at '^' marker.

%Default route without gateway, if not a point-to-point interface, may impact performance

Password:

*Mar  1 00:00:47.195: %LINK-6-UPDOWN: Interface BVI1, changed state to down

*Mar  1 00:00:48.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down

AP5006.04a6.231e>enable

Password:

AP5006.04a6.231e#conf te

                  ^

% Invalid input detected at '^' marker.

6 REPLIES
New Member

Aironet 702 - configuration issue

if, the ethernet and radio interface is up kindly check if the band is selected means a,b,g & n.

New Member

I have the same problem .I

I have the same problem .

I can login to the CAP702i through the console port, but can't get access to the "Configuration terminal" commands.

I am thinking the the Flash file "ap1g1-rcvk9w8-mx.152-4.JA" is the issue.

I have downloaded an updated file from the Cisco web site, but with not way to install it, I can't determine if it is what's causing the problem.

I connected the CAP702i to a DHCP server, and it is pulling a valid IP, but I am unable to Telnet, browse or use Network Assistant to access the GUI setup.

I am able to ping the CAP702i, but that's about extent of it functionality so far.

 

 

 

 

New Member

Hi Buddy Did you find a fix

Hi Buddy

 

Did you find a fix to this? I have the exact same problem on a 702W

 

Kamran

New Member

The problem was that I

The problem was that I purchased the wrong model:

CAP702I  - CAP = Controller based Access Point.

SAP702I   - SAP = Standalone Access Point.

Either return the CAP model for a SAP model or you need to download and update the firmware

for a SAP702i.

The proper firmware can be found on the Cisco Support site. (link below)

The file I used : ag1g1-k9w7-tar.152-4.JB5.tar

http://software.cisco.com/download/release.html?mdfid=284741752&softwareid=284180979&os=&release=15.2.4-JB5&relind=AVAILABLE&rellifecycle=&reltype=latest&i=!pp

You will need to connect the AP702 to a DHCP server so it can grab a IP address.

Install the Cisco HTTP program to update the Firmware, and reboot the AP702.

 

New Member

Hi I have the same Issue, can

Hi

 

I have the same Issue, can you explain what is the Cisco HTTP program?

The AP is always renewing the IP using DHCP because it doesn't find a WLC.

Thank you

Best Regards

New Member

I will attach the

I will attach the configuration manual I used to transfer the new firmware file.

scg15_2_4_JB3a.pdf

The commands are pretty vague in the manual, and if you are not familiar the command structure, I would contact Cisco support.

You will need to install the TFTP server and have the firmware file before contacting support.

 

1316
Views
0
Helpful
6
Replies
CreatePlease to create content