Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements
Webcast-Catalyst9k
New Member

Al añadir puertos a una Vlan no se conectan a la Red

Buenos Dias,

Saludos a todos,

Tengo un inconveniente con un SW 2960G desde el dia de ayer y es que  al añadir puertos a una VLAN en particular (VLAN 2), los equipos no se conectan a la red.Realice la configuracion en 4 puertos(15/34/35/36) y en ninguno quiso conectarse.Desde el Sw logro hacerle ping al servidor, sin embargo desde otro equipo conectado en el mismo SW, perteneciente a la misma vlan no logro hacerle pin.Los puertos negocian la velocidad y llegan a estar UP.

Ahora bien, cuando a esos mismos puertos les configuro otra vlan,(vlan 7) los equipos logran entrar en la red sin problemas.Si configuro la VLAN 2 en otro SW los equipos se conectan sin problemas.

Hasta ahora no hay mas de 100 equipos conectados a la VLAN 2.

SW1_SERVERS#sh vlan

VLAN Name                             Status    Ports

---- -------------------------------- --------- -------------------------------

1    default                          active  

2    VLAN0002                     active    Gi0/1, Gi0/2, Gi0/4, Gi0/5, Gi0/6, Gi0/7, Gi0/8, Gi0/9, Gi0/10, Gi0/11, Gi0/12

                                                Gi0/13, Gi0/14, Gi0/15, Gi0/16, Gi0/17, Gi0/18, Gi0/20, Gi0/21, Gi0/22, Gi0/23

                                                Gi0/24, Gi0/25, Gi0/26, Gi0/27, Gi0/28, Gi0/30, Gi0/31, Gi0/32, Gi0/33, Gi0/34

                                                Gi0/35,Gi0/36, Gi0/45, Gi0/46, Gi0/47, Gi0/48

3    VLAN0003                         active    Gi0/19

6    VLAN0006                         active    Gi0/3, Gi0/37

7    Red_140                          active    Gi0/29, Gi0/38

1002 fddi-default                     act/unsup

1003 token-ring-default               act/unsup

1004 fddinet-default                  act/unsup

1005 trnet-default                    act/unsup

Cisco IOS Software, C2960 Software (C2960-LANBASEK9-M), Version 12.2(44)SE6, RELEASE SOFTWARE (fc1)

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Mon 09-Mar-09 18:10 by gereddy

Image text-base: 0x00003000, data-base: 0x01100000

ROM: Bootstrap program is C2960 boot loader

BOOTLDR: C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(44)SE6, RELEASE SOFTWARE (fc1)

SW1_SERVERS uptime is 5 weeks, 2 days, 17 hours, 35 minutes

System returned to ROM by power-on

System image file is "flash:c2960-lanbasek9-mz.122-44.SE6/c2960-lanbasek9-mz.122-44.SE6.bin"

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco WS-C2960G-48TC-L (PowerPC405) processor (revision F0) with 61440K/4088K bytes of memory.

Processor board ID FOC1416V5PH

Last reset from power-on

2 Virtual Ethernet interfaces

48 Gigabit Ethernet interfaces

The password-recovery mechanism is enabled.

64K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address       : 1C:17:D3:46:47:00

Motherboard assembly number     : 73-10300-09

Power supply part number        : 341-0098-02

Motherboard serial number       : FOC14171N1F

Power supply serial number      : AZS141608H0

Model revision number           : F0

Motherboard revision number     : A0

Model number                    : WS-C2960G-48TC-L

System serial number            : FOC1416V5PH

Top Assembly Part Number        : 800-27071-04

Top Assembly Revision Number    : C0

Version ID                      : V04

CLEI Code Number                : COMFV00BRA

Hardware Board Revision Number  : 0x01

Switch Ports Model              SW Version            SW Image                

------ ----- -----              ----------            ----------              

*    1 48    WS-C2960G-48TC-L   12.2(44)SE6           C2960-LANBASEK9-M 

Configuracion de Interfaz

interface GigabitEthernet0/15

switchport access vlan 2

switchport mode access

speed auto 1000     

Alguien le ha pasado algo parecido??

Saludos,

Everyone's tags (2)
2 REPLIES
Hall of Fame Super Bronze

Al añadir puertos a una Vlan no se conectan a la Red

Try adding 'spanning-tree portfast' to GigabitEthernet0/15

Regards,

Edison

New Member

Al añadir puertos a una Vlan no se conectan a la Red

Buenas Tardes;

Se añadio el  spanning-tree portfast y no hubo ningun cambio seguimos con la falla .

528
Views
0
Helpful
2
Replies
CreatePlease to create content