Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Anyone knows if the 2651XM support port-channel?

Hi,

I want to set the two Fa port on 2651XM to be a port channel, but don't see the channel-group command under the interface. I did try few IOS, they are the same. Does the 2651XM support this?

Thanks,

Ryan

Everyone's tags (3)
2 ACCEPTED SOLUTIONS

Accepted Solutions
Cisco Employee

Anyone knows if the 2651XM support port-channel?

Hello Ryan,

The routed ports on this router do not support bundling into EtherChannel. I suppose that the only EtherChannel supported on 2651XM can be configured on switchports of installed HWIC or NM switching modules.

I am sorry to disappoint you here.

Best regards,

Peter

Super Bronze

Anyone knows if the 2651XM support port-channel?

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

The first ISR series I know that supports EtherChannel on its built-in ports is the 2800 series.

5 REPLIES
Cisco Employee

Anyone knows if the 2651XM support port-channel?

Hello Ryan,

The routed ports on this router do not support bundling into EtherChannel. I suppose that the only EtherChannel supported on 2651XM can be configured on switchports of installed HWIC or NM switching modules.

I am sorry to disappoint you here.

Best regards,

Peter

Super Bronze

Anyone knows if the 2651XM support port-channel?

Disclaimer

The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.

Liability Disclaimer

In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.

Posting

The first ISR series I know that supports EtherChannel on its built-in ports is the 2800 series.

Cisco Employee

Re: Anyone knows if the 2651XM support port-channel?

Hello Joseph,

This surprises me a lot. I do not currently have any access to 2811 or higher but the 2801 I have handy does not appear to support it:

Cisco IOS Software, 2801 Software (C2801-ADVIPSERVICESK9-M), Version 12.4(4)XC2, RELEASE SOFTWARE (fc1)

Synched to technology version 12.4(5.13)T

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Sat 29-Apr-06 02:39 by ealyon

Router(config)#int fa0/0

Router(config-if)#channel?

% Unrecognized command

Best regards,

Peter

Super Bronze

Re: Anyone knows if the 2651XM support port-channel?

Disclaimer

The  Author of this posting offers the information contained within this  posting without consideration and with the reader's understanding that  there's no implied or expressed suitability or fitness for any purpose.  Information provided is for informational purposes only and should not  be construed as rendering professional advice of any kind. Usage of this  posting's information is solely at reader's own risk.

Liability Disclaimer

In  no event shall Author be liable for any damages whatsoever (including,  without limitation, damages for loss of use, data or profit) arising out  of the use or inability to use the posting's information even if Author  has been advised of the possibility of such damage.

Posting

Peter, oops, except the 2801 -  I should have noted that.

See http://www.cisco.com/en/US/prod/collateral/routers/ps5855/prod_white_paper0900aecd806f698a.pdf

Cisco Employee

Re: Anyone knows if the 2651XM support port-channel?

Hi Joseph,

Wow! +5 points. I did not know about this! Thank you!

Best regards,

Peter

320
Views
5
Helpful
5
Replies
CreatePlease to create content