11-28-2007 05:51 PM - edited 03-05-2019 07:41 PM
ap1231g unable to pass traffic thru gigabit int on WS-X6148A-GE-45AF.
switchport settings:
interface GigabitEthernet9/1
description wireless: AP-020
switchport
switchport trunk encapsulation dot1q
switchport trunk native vlan 301
switchport mode trunk
no ip address
no snmp trap link-status
----------------
sh int trunk status:
Port Mode Encapsulation Status Native vlan
Gi5/1 on 802.1q trunking 999
Gi9/1 on 802.1q trunking 301
-------------------------
sh cdp nei detail:
Device ID: myworkplace-AP-020.xyz.com
Entry address(es):
IP address: 10.1.194.88
Platform: cisco AIR-AP1231G-A-K9 , Capabilities: Trans-Bridge
Interface: GigabitEthernet9/1, Port ID (outgoing port): FastEthernet0
Holdtime : 130 sec
Version :
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 27-Apr-07 00:59 by hqluong
advertisement version: 2
Duplex: full
Power drawn: 4.420 Watts
-------------------
AP1231G config:
interface Dot11Radio0.299
encapsulation dot1Q 299
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
!
interface Dot11Radio0.301
encapsulation dot1Q 301 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
!
interface FastEthernet0.299
encapsulation dot1Q 299
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
!
interface FastEthernet0.301
encapsulation dot1Q 301 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
description wireless: AP-020
ip address 10.1.194.88 255.255.255.224
no ip route-cache
!
ip default-gateway 10.1.194.65
- unable to ping default gateway or ANY other device on vlan
- ints are all up/up
- tried replacing with known good wap, no success
NOTE: known good wap is connected to C3750 switch and works fine.
is issue due to gig interface compatability? i've tried chging speed/duplex settings but nothing works.
here is module info:
9 48 48-port 10/100/1000 RJ45 EtherModule WS-X6148A-GE-45AF
9 0019.e8ac.5ff0 to 0019.e8ac.601f 2.2 8.4(1) 8.5(0.46)RFW Ok
Thanks for any info
11-28-2007 10:41 PM
My suggestion is to fiddle with the bridge group settings:
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source <
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
Are all these settings absolutely required? It is always good practice to start with a basic configuration, then add the required lines for fine tuning.
regards,
Leo
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: