Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

ASR9K Interface Input Errors?

All,

I got a ticket today and it was in regard to the error count on one of the TenG interfaces on one of our ASR9K's. In looking at the interface I noticed quite a few Input Errors on the port. I cleared the counters and monitored. In checking the port again I saw the Input Errors again incrementing. On the smaller Cisco switches you can ususally run the show interface gig 1/1/1 counters error command. With the ASRs you can not. I am wondering if someone could explain what the Input Errors could mean. Media issue? Incorrect Setting? Not sure what I need to be looking at being I have little time on the ASR's at this point. Thanks.          

Regards,
Mark       

Regards, Mark
  • LAN Switching and Routing
4 REPLIES

ASR9K Interface Input Errors?

Can you post the "sh int tengige1 x/y/z" output for us to see more info?

Troubleshooting Ethernet http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr1904.html

New Member

ASR9K Interface Input Errors?

Here you are:

RP/0/RSP1/CPU0:rx-cssclabqa-b217-3-core#sh int tenGigE 0/0/0/30

Thu Jan 23 09:45:23.702 CST

TenGigE0/0/0/30 is up, line protocol is up

  Interface state transitions: 5

  Hardware is TenGigE, address is 8478.ac2b.8ce6 (bia 8478.ac2b.8ce6)

  Layer 1 Transport Mode is LAN

  Internet address is Unknown

  MTU 1514 bytes, BW 10000000 Kbit (Max: 10000000 Kbit)

     reliability 248/255, txload 0/255, rxload 0/255

  Encapsulation ARPA,

  Full-duplex, 10000Mb/s, link type is force-up

  output flow control is off, input flow control is off

  loopback not set,

  Last input 00:00:08, output never

  Last clearing of "show interface" counters 20:39:33

  5 minute input rate 0 bits/sec, 0 packets/sec

  5 minute output rate 0 bits/sec, 0 packets/sec

     1239 packets input, 341964 bytes, 0 total input drops

     0 drops for unrecognized upper-level protocol

     Received 0 broadcast packets, 1239 multicast packets

              0 runts, 0 giants, 0 throttles, 0 parity

    409 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

     0 packets output, 0 bytes, 0 total output drops

     Output 0 broadcast packets, 0 multicast packets

     0 output errors, 0 underruns, 0 applique, 0 resets

     0 output buffer failures, 0 output buffers swapped out

     0 carrier transitions

Regards,
Mark

Regards, Mark

Re: ASR9K Interface Input Errors?

The interface RELIABILITY is also low.

The speed/duplex configuration of the interface in the local device is forced.

What is the configuration of the remote device interface?

Could be a duplex mismatch or bad cabling.

New Member

If i'm not mistaken, you

If i'm not mistaken, you cannot set negotiation to auto on a TenGigE interface on an ASR9K, or any 10G interface in any device for that matter.

Im having the same issue, but also showing CRCs. Already replaced the cabling.

667
Views
0
Helpful
4
Replies
This widget could not be displayed.