Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

auto qos in WS-C4507R

I need knows if this WS-C4507R support the command auto qos voip trust and what is the best way to configure QOS in the LAN.

------------------ show version ------------------

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EW, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2004 by Cisco Systems, Inc.

Compiled Fri 10-Dec-04 14:26 by kellythw

ROM: 12.2(20r)EW1

Dagobah Revision 95, Swamp Revision 6

8901SW254 uptime is 1 year, 25 weeks, 3 days, 1 hour, 32 minutes

Uptime for this control processor is 1 year, 25 weeks, 3 days, 1 hour, 32 minutes

System returned to ROM by power-on

System restarted at 10:22:00 UTC Thu Nov 2 2006

System image file is "bootflash:"

cisco WS-C4507R (MPC8245) processor (revision 8) with 524288K bytes of memory.

Processor board ID FOX0851021H

MPC8245 CPU at 400Mhz, Supervisor V

Last reset from PowerUp

8 Virtual Ethernet interfaces

58 Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAB0905024M

2 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAB090604EF

3 24 10/100/1000BaseT (RJ45) WS-X4424-GB-RJ45 JAE084501JM

4 24 10/100/1000BaseT (RJ45) WS-X4424-GB-RJ45 JAE08501ZAQ

5 6 1000BaseX (GBIC) WS-X4306-GB JAE1123KT0L

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0013.1a1f.3b00 to 0013.1a1f.3b01 2.0 12.2(20r)EW1 12.2(25)EW Ok

2 0013.1a1f.3b02 to 0013.1a1f.3b03 2.0 12.2(20r)EW1 12.2(25)EW, Ok

3 0012.01f1.97e0 to 0012.01f1.97f7 1.6 Ok

4 0012.01f1.ccc0 to 0012.01f1.ccd7 1.6 Ok

5 000e.83a1.c4e8 to 000e.83a1.c4ed 4.3 Ok

------------------ show bootflash: all ------------------

-#- ED ----type---- --crc--- -seek-- nlen -length- ---------date/time--------- name

1 .. image F0AB9628 C4C440 28 12370880 Feb 9 2005 04:23:53 -06:00 cat4000-i9s-mz.122-25.EW.bin

46873536 bytes available (12371008 bytes used)

anyone can help me?

3 REPLIES
Super Bronze

Re: auto qos in WS-C4507R

I'm unfamiliar with the 4500 series QoS specifically, or whether it supports any auto QoS features, but in general, either a two class model (real-time and BE), or a four class model (e.g. real-time, better than BE, BE and less than BE) model works well. (Many LAN switches that support QoS/CoS, usually only support two or four classes.)

How to use the four class model, real-time traffic, like VoIP in a LLQ class; really important/critical (and hopefully lightweight) traffic, like voice signally, in the better then BE class (minimal bandwidth guarantee sufficient so traffic usually doesn't queue); really bad traffic, like server network backups, in the less than BE class with a minimal bandwidth guarantee (perhaps only 1%); everything else in BE.

[edit]

PS:

The software configuration guides for your IOS version should have a section about QoS.

New Member

Re: auto qos in WS-C4507R

thansk for your reply, can you tell me how to find a configuration guide for my IOS version?

thanks

Super Bronze
253
Views
0
Helpful
3
Replies