Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Auto QOS on 6500 with Sup32-10G gives warning errors

We've enabled auto qos on our 6504 w/sup32-10G on our ws-6148a blades and are receiving the following errors. Is this normal? Code is the latest out: 12.2(33)SXH2, switches are runnin as L2 devices only (no routing):

Warning: rcv cosmap will not be applied in hardware.

To modify rcv cosmap in hardware, all of the interfaces below

must be put into 'trust cos' state:

Gi3/1 Gi3/2 Gi3/3 Gi3/4 Gi3/5 Gi3/6 Gi3/7 Gi3/8 Gi3/9 Gi3/10 Gi3/11 Gi3/12 Gi3/13 Gi3/14 Gi3/15 Gi3/16 Gi3/17 Gi3/18 Gi3/19 Gi3/20 Gi3/21 Gi3/22 Gi3/23 Gi3/24 Gi3/25 Gi3/26 Gi3/27 Gi3/28 Gi3/29 Gi3/30 Gi3/31 Gi3/32 Gi3/33 Gi3/34 Gi3/35 Gi3/36 Gi3/37 Gi3/38 Gi3/39 Gi3/40 Gi3/41 Gi3/42 Gi3/43 Gi3/44 Gi3/45 Gi3/46 Gi3/47 Gi3/48

threshold configured on all 48 ports on slot 3.

Should config changes be made to the cos trust to utilize hardware capabilities?

Thanks,

-Scott

2 REPLIES
Silver

Re: Auto QOS on 6500 with Sup32-10G gives warning errors

Use the "Interface Range" command and try to disable it on all the interfaces on the module.

By default, you should not see the "rcv-queue .." configurations under the interface. In order to remove the configuration,

try the following commands.

Interface range Gi1/1 - 1/12

Mls qos trust cos

No rcv-queue cos-map

No mls qos trust cos

New Member

Re: Auto QOS on 6500 with Sup32-10G gives warning errors

Thanks for the suggestion. Below are the current port configuration for an auto qos port with pc/phone, as well as the commands I tried on a set of selective interfaces (G3/1 -2). I get an error regarding the asic. Since we have phone ports requiring auto qos voip cisco-phone intermixed (non sequential) with access only ports (printers, scanners, etc), this may present a problem on the 6500's.

This problem does not exist on the 4500 series chassis. :-/

interface GigabitEthernet3/1

description Test PC and Phone

switchport

switchport access vlan xx

switchport mode access

switchport voice vlan xy

wrr-queue bandwidth 20 100 200

priority-queue queue-limit 5

wrr-queue queue-limit 65 15 15

wrr-queue random-detect min-threshold 1 70 100 100 100 100 100 100 100

wrr-queue random-detect min-threshold 2 70 100 100 100 100 100 100 100

wrr-queue random-detect min-threshold 3 40 40 50 50 60 60 70 70

wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100

wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100

wrr-queue random-detect max-threshold 3 70 70 80 80 90 90 100 100

wrr-queue cos-map 2 1 1 2

wrr-queue cos-map 3 5 3 4

wrr-queue cos-map 3 7 6 7

mls qos trust cos

auto qos voip cisco-phone

spanning-tree portfast

Error message below when int range is attempted on G3/1 -2 (both phone ports):

switch-lab1(config-if-range)#mls qos trust cos

switch-lab1(config-if-range)#no rcv-queue cos-map

Warning: Can't remove cos-map because configuration is used by some other port(s) on this ASIC which has AutoQoS enabled

Warning: Can't remove cos-map because configuration is used by some other port(s) on this ASIC which has AutoQoS enabled

2815
Views
0
Helpful
2
Replies
CreatePlease login to create content