Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 

Switching

Discuss Catalyst brand switches with peers and experts.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Get 20% off switches when you combine Cisco solutions

 
Labels

Forum Posts

Start a conversation

Resolved! Configuracion de Switches y Load Balancer

Hola, deseo hacerles una consulta, planeo instalar 200 nodos con un servicio de internet de 10/10mb utilizar un Cisco SG300-10SFP-K9 Small Bus Switch 10/100/1000 para balancear la carga de internet y subdividir a 4 Cisco Catalys 52-port Gigabit PoE M...

upgrade inside host to ASA 5505

I bought an ASA 5505 (ASA5505-BUN-K9). I see the limit of 10 inside users.What is the solution for upgrade this limit? Is there a license for increase this value?I buy and install the license L-ASA5505-SECPL= but the limit of inside users is the same...

Resolved! Nexus F2 Modules clarification

Dears,Attached are the 2 no's screenshot 1 no's is the screenshot from the datasheet where the cisco  says the he fabric architecture scales beyond 15 terabits per second (Tbps), How cisco calculate figure 15 TB ???? The Nexus 2 screenshot attached  ...

ASA 5505 Port forwarding

Dear All,   We have an ASA 5505 8.4 with ASDM 6.4 ASA has a PPPOE in outside interface. We have a DVR sitting at 192.168.1.120 behind the inside interface. We need to forward ports 8000 & 8001. I applied the following rules to allow the traffic to fl...

sriram003 by • Level 1
  • 148 Views
  • 1 replies
  • 0 Helpful votes

Nexus 5K SAN Port-channel - Invalid Range

Hello, I don´t know if someone can help me in this setup. whenever I try to create a san port channel in a nexus 5K I always get the following message error,"Invalid range" I think that I´ve installed all the features necessary to this but the proble...

Resolved! Port security with Access Points connected

We have a site where we are using Meraki access points. The problem we are having is that some users keep disconnecting the APs to hard wire into the wall port. Am I right in thinking that I cannot use port security on the switch for these ports as w...

4506-e with sup8 in vss need qos config for voip

hi, i have 4506-e with sup8 running in vss mode and i needed to make sure voip traffic is preserved and prioritize.network set-up:cisco phone---->2960-x----->etherchannel-->>4506-e auto qos is already configured in 2960 switches and as what i underst...

SirEna by • Level 1
  • 310 Views
  • 1 replies
  • 0 Helpful votes

Cisco 3850 24T Switch Stack Config

Dear Friends, I have 2nos Cisco 2850 Switches,I am new to stack config, I know by default stack will be enabled but I want to change the priority..So Please help me stack config  step by step.... Thanks & Regards,Srinivas. N

Is it recommended to use HSRP or multiple default between Core Layer Switch and Customer Edge Router?

My client is asking me for followingClient is using Router as edge device. 2  WAN links from different service provider ( each 20 Mbps)  are getting terminated on the router. There are internal servers present in the network. Client want to make setu...

Resolved! L2 Vlan over L3 link

HiPlease see attachment for my setup. So I have 2 sites which are approx half a mile apart. The ISP has provided 2 circuits, one at each site and these are meant to be acting as a Active/Standby circuit for which they will use HSRP. They have asked u...

SPAN To Hyper-V

Hi All,We want to setup SPAN, and its source is a physical port on the catalyst switch and the destination is a VM on a Hyper-V host, the hyper-V host has 4 NICs and we can not Dispense about any NIC.And I want to ask how can we do this without a ded...

View All
Review Cisco Networking products for a $25 gift card