HiOur monitoring tool (solar wind) is showing Transmit discards on the interface between border router ( ASR1004) and core switch (WS-C6509-E).But i don't see the error when i check the router or switch. NODE INTERFACE Rx_ERRORS Rx_DISCA...
Hi All,I have read all I can on GLBP without a definitive answer to my question. I have two 7613 routers connected to two 7304's that serve as our gateways to the ISP. I would like to run these connections through a 6509VSS and run GLBP on all 4 rout...
Hi, I have two Nexus 7K, one at each datacenter. They are connected via 10G Ethernet. Both Nexus cores are running OSPF between them. Below are their configs:Nexus 1:interface Vlan10 no ip redirects ip address 10.0.0.2/22 ip router ospf 3900 area...
I have checked over documents on cisco.com but still unclear.We would like to start stacking some 2960S switches. We currently have one 2960S in production now, and are ready to create the stack with a second 2960S. A few questions regarding this:Doe...
Hello,I have configured different network on two different interfaces of firewall. Both interfaces are connected with different Cisco switches and hosts on them......configured static route, access policy like "any-any", services like ip, icmp etc., ...
Hello.I was hoping that someone could over some suggestions on best practice or recommendations for configuring port channel to bundle to layer 2 MPLS links that we have.We have racks in two geographically separated data centres, each rack has a stac...
hi, I bought new Cisco Aironet 702. I have problem with configuration. I can't access to configure terminal option or to web setup. Below is startup screens from Aironet. There are few errors during startup process:no ip http server ^% Invalid...
HiThe WS-X6716-10GE in slot 3 has a problem for links:%C6K_PLATFORM-6-OVERSUB_INFO_VS: switch-id 1 Module 3 port-group 2 (ports 5 6 7 8) is operating in oversubscription mode. In case only port 5 of port-group 2 is to be used, enalbe non oversubscri...
I have cisco Aironet 1040 Series APs through out my Church. They are all wired to a main router RV220W. I have two Vlans setup one is Open (non secured) for Church members guestThe other is secured WPA2 for Church staff members. Both are on a differ...
Hello Everyone, I have 2 switches named in the title that have Switchport mode Trunk Native Vlan 55. In the vlan configurations I do not see a Vlan 55. Does anyone know why this is configured this way ? P.S I am new to the config
Dear, This question has been bugging my mind lately, say you configure a switch to put it inside a VTP domain. Let's say the access vlan has to be 8 and voice 10.If you preconfigure the ports the switch will auto create the vlan locally to the switch...
Dears Hello PLease I faced the following Error Message in my switch c3750x TE ver 15 , please let me know what is this error , does my switch has bug ? %TCP-2-INVALIDTCB: Invalid TCB pointer: 0x7B7A89C -Process= "HTTP CORE", ipl= 0, pid= 301-Traceb...
We are in process of setting up vPC peer between 2 N7ks over a 1Gig link, has anybody done this before? Couldn't find any documents in cisco site which talks about this. All of the documents points to setting up using 10G links. CheersRaja
i need help please, i have avaya ip office 500 connected direct to CORE SWITCH 3750 X. i'm trying to ping but the ping is high duplex is full in bothspeed 100 in bothcable is testedi changed the cisco switch port and still the same problem. help me...
We have 2 cisco 1921routers (R1 and R1) both have 2 interfaces Gi0/0 and Gi0/1. We have 2 cisco 2960G Ethernet switches S1 and S2 are connected to each other. Each router is connected to both Ethernet switches. On each router has Gi0/0 as the primary...
