11-28-2009 10:10 AM - edited 03-06-2019 08:45 AM
Solved! Go to Solution.
11-28-2009 11:19 AM
r.taccon wrote:
Hi,need to configure a BGP between 2 switched cisco 3750.I've configured the BGP but I can't distribute the net 200.168.57.168/27 to the sw3750NUMBER2 (see below the conf.).Please can someone help me ?sw3750NUMBER1!interface Vlan3231description ** BGP session interface **ip address 169.254.231.1 255.255.255.248!router bgp 65534no synchronizationbgp router-id 169.254.231.1bgp log-neighbor-changesnetwork 192.168.57.128 mask 255.255.255.224neighbor 169.254.231.5 remote-as 65532neighbor 169.254.231.5 transport path-mtu-discoveryneighbor 169.254.231.5 description ** to - sw3750NUMBER2 - Vlan3231 **neighbor 169.254.231.5 update-source Vlan3231neighbor 169.254.231.5 soft-reconfiguration inboundneighbor 169.254.231.5 prefix-list 169.254.231.5-in inneighbor 169.254.231.5 prefix-list 169.254.231.5-out outno auto-summary!!ip prefix-list 169.254.231.5-in seq 5 permit 169.254.231.0/29!ip prefix-list 169.254.231.5-out seq 5 permit 169.254.231.0/29ip prefix-list 169.254.231.5-out seq 10 permit 192.168.57.128/27ip prefix-list 169.254.231.5-out seq 15 permit 200.168.57.128/27!
Is this a typo in your router bgp config because you do not have a network statement for that route so unless you are receiving it from another peer you will need to add in a network statement. You will also need an entry in the routing table on switch1 for that network
router bgp 65534
network 200.168.57.128 mask 255.255.255.224
Jon
11-28-2009 11:19 AM
r.taccon wrote:
Hi,need to configure a BGP between 2 switched cisco 3750.I've configured the BGP but I can't distribute the net 200.168.57.168/27 to the sw3750NUMBER2 (see below the conf.).Please can someone help me ?sw3750NUMBER1!interface Vlan3231description ** BGP session interface **ip address 169.254.231.1 255.255.255.248!router bgp 65534no synchronizationbgp router-id 169.254.231.1bgp log-neighbor-changesnetwork 192.168.57.128 mask 255.255.255.224neighbor 169.254.231.5 remote-as 65532neighbor 169.254.231.5 transport path-mtu-discoveryneighbor 169.254.231.5 description ** to - sw3750NUMBER2 - Vlan3231 **neighbor 169.254.231.5 update-source Vlan3231neighbor 169.254.231.5 soft-reconfiguration inboundneighbor 169.254.231.5 prefix-list 169.254.231.5-in inneighbor 169.254.231.5 prefix-list 169.254.231.5-out outno auto-summary!!ip prefix-list 169.254.231.5-in seq 5 permit 169.254.231.0/29!ip prefix-list 169.254.231.5-out seq 5 permit 169.254.231.0/29ip prefix-list 169.254.231.5-out seq 10 permit 192.168.57.128/27ip prefix-list 169.254.231.5-out seq 15 permit 200.168.57.128/27!
Is this a typo in your router bgp config because you do not have a network statement for that route so unless you are receiving it from another peer you will need to add in a network statement. You will also need an entry in the routing table on switch1 for that network
router bgp 65534
network 200.168.57.128 mask 255.255.255.224
Jon
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: