Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

boot system configuration in 3750 stack switch

boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin

We have two stack of 3750 switches. When I enter above command getting below mentioned error, two images are showing switch 1, but one image only showing in switch 2, i.e 1st image in show boot command.

%Command to set boot system switch all  flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin  on switch=2 failed

Please advice, what could be the issue.

5 REPLIES
VIP Super Bronze

boot system configuration in 3750 stack switch

SEE2.bin??

shouldn't this be

SE2.bin or the same image as the first switch SEE1.bin

Have a look at this doc for example:

http://www.cisco.com/en/US/products/hw/switches/ps5023/products_configuration_example09186a00804799d7.shtml

HTH

Hall of Fame Super Gold

boot system configuration in 3750 stack switch

Please reboot the switch, post the entire bootup process.  The error message you've posted is incomplete to begin analysis of the issue.

Silver

boot system configuration in 3750 stack switch

hari babu wrote:

boot system switch all flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin

We have two stack of 3750 switches. When I enter above command getting below mentioned error, two images are showing switch 1, but one image only showing in switch 2, i.e 1st image in show boot command.

%Command to set boot system switch all  flash:c3750-ipservicesk9-mz.122-55.SE1/c3750-ipservicesk9-mz.122-55.SE1.bin;flash:c3750-ipservices-mz.122-25.SEE2/c3750-ipservices-mz.122-25.SEE2.bin  on switch=2 failed

Please advice, what could be the issue.

Do you actually have the required files on the flash in BOTH switches in the stack?

What do the following commands show

dir flash1:

dir flash2:

Cheers.

Cisco Employee

boot system configuration in 3750 stack switch

-Please check if both the images are present on the flash of respective switches. (use dir flash1: and dir flash2:)

-Try setting the boot variable for two images seperately. First set for SE1 and then SEE2. This should help.

-Sweta

*Please rate useful posts.

Silver

boot system configuration in 3750 stack switch

You should have the same IOS image on both switches in order for them to boot properly. The only exception to the rule of course is if you stack a 3750E with standard 3750s.

The easiest fix I can think of would be to copy the IOS from your master switch to your slave switch. If you need commands on how to copy across the switch stack don't hesitate to ask.

---

Posted by WebUser Adam Sibille

5316
Views
0
Helpful
5
Replies
CreatePlease to create content