Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

booting after softreset

my catalyst 2950 is resuming after give this message (booting after softreset )

can any one help me what to do .

4 REPLIES

Re: booting after softreset

Hi

can you paste the exact message you are seeing out there during booting ?

regds

New Member

Re: booting after softreset

thanks for reply below is the message i am geting & switch is booting , booting .....

Loading "flash:/c2950-i6q4l2-mz.121-22.EA7.bin"...##############################

################################################################################

################################################################################

##########

File "flash:/c2950-i6q4l2-mz.121-22.EA7.bin" uncompressed and installed, entry p

oint: 0x80010000

executing...

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA7, RELEASE SOFTWARE

(fc1)

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Fri 27-Jan-06 21:19 by antonino

Image text-base: 0x80010000, data-base: 0x8056A000

Initializing flashfs...

flashfs[1]: 598 files, 5 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 7741440

flashfs[1]: Bytes used: 5101568

flashfs[1]: Bytes available: 2639872

flashfs[1]: flashfs fsck took 8 seconds.

flashfs[1]: Initialization complete.

Done initializing flashfs.

POST: System Board Test : Passed

The MAC Address has not been set in the environment.

Using default address: 04:04:04:00:00:01

POST: Ethernet Controller Test : Passed

ASIC Initialization Passed

The MAC Address has not been set in the environment.

Using default address: 04:04:04:00:00:01

POST: FRONT-END LOOPBACK TEST : Passedcisco WS-C2950-24 (RC32300) processor with

21004K bytes of memory.

Last reset from system-reset

Running Standard Image

24 FastEthernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.

Invalid parameter block -- no serial number or mac address available.

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]:

=== Flushing messages (00:00:19 UTC Mon Mar 1 1993) ===

Buffered messages:

Queued messages:

00:00:19: %SYS-3-LOGGER_FLUSHING: System pausing to ensure console debugging out

put.

00:00:16: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for type vlan

00:00:17: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected

Signal 10, Exception code (0x0008)!

Frame 00: SP = 0x80B90E80 PC = 0x802D2A90

Frame 01: SP = 0x80B90E98 PC = 0x802D30DC

Frame 02: SP = 0x80B90EB8 PC = 0x80191D48

Frame 03: SP = 0x80B90EE8 PC = 0x8034FFA0

Frame 04: SP = 0x80B90F00 PC = 0x803056CC

Frame 05: SP = 0x80B90F18 PC = 0x8011FD20

Frame 06: SP = 0x80B91028 PC = 0x801BC908

Frame 07: SP = 0x80B91040 PC = 0x801BC8F4

=== Crash Fault History ===

C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA7, RELEASE SOFTWARE (fc1)

Compiled Fri 27-Jan-06 21:19 by antonino

Signal = 10, Code = 0x8, Uptime 00:00:19

r0: 00000000, AT: 00000000, v0: 00000000, v1: 8066644C

a0: 00000030, a1: 000000FF, a2: 80660000, a3: 80C93CC0

t0: 00000018, t1: 1000E101, t2: 1000E100, t3: FFFF00FF

t4: 802D20B0, t5: A08C24A0, t6: 00000000, t7: A08C2498

s0: 00000000, s1: 80D12704, s2: 00000000, s3: 00000000

s4: 80865F90, s5: 80860000, s6: 80B90FF8, s7: 80850000

t8: A08C250C, t9: 00000000, k0: 00000000, k1: 00000000

gp: 807DED20, sp: 80B90E80, s8: 80870000, ra: 802D2A90

EPC: 802D2A90, ErrEPC: 02E98041, BadVA: 0x0000003C, SREG: 1000E103

Cause: 0x00000008 (code 2): TLB (load or ifetch) exception

-Traceback= 802D2A90 802D30DC 80191D48 8034FFA0 803056CC 8011FD20 801BC908 801BC

8F4

Booting after a softreset ...

Re: booting after softreset

Log says that "Internal Power Supply has gone faulty".

Let me know is there any RPS/External Power Supply is connected to this switch ??

Most probably, you will have to replace the switch.!!!

Purple

Re: booting after softreset

Sounds like the internal supply has failed and its running on a RPS like a rps 2300 .

1019
Views
0
Helpful
4
Replies