06-15-2010 10:19 AM - edited 03-06-2019 11:35 AM
Hii Experts,
Wht is the command to stop the Broadcast traffic from remote site connected on Switch Port (L2 port).
06-15-2010 11:07 AM
Hello Netbeginner,
storm-control
see
be aware that are some differences depending on the type of supervisor you have
Hope to help
Giuseppe
06-16-2010 07:48 AM
Hii Experts,
Wht is the command to stop the Broadcast traffic from remote site connected on Switch Port (L2 port).
Hi,
Storm-Control can be used to limit, or to set thresholds for different types of traffic (Broadcast, Multicast and Unicast) on a specific interface you choose (or that you´re asked for).You can set your threshold to whatever the top level that you want, and the traffic will be limit to that.
The following example will enable Unicast Storm-Control on a switch port with an 89% rising suppression level and a 67% falling suppression (remember, falling suppression can only be configured in 3560). It´ll also enable Broadcast Storm-Control on a port to a level of 20%. When the Broadcast exceeds the configured level of 20% of the total available bandwidth of the port within the traffic-storm-control interval, the switch drops all broadcast traffic until the end of the traffic-storm-control interval:
interface gigabitethernet0/1
storm-control unicast level 89 67
storm-control broadcast level 20
Hope to Help !!
Ganesh.H
Remember to rate the helpful post
06-17-2010 10:47 AM
Hi Ganesh & Guise,
Implemented the command on L3 switch gig interface (Cisco 4500 series).
interface GigabitEthernet4/36
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2,4,6
switchport mode trunk
speed 100
duplex full
udld port aggressive
storm-control broadcast level 0.00
We have given Level % "0", As per understanding If we configure the 0% level then there should not be any single broadcast on the interface. But even after this we are getting broadcast on the interface.
5 minute input rate 807000 bits/sec, 326 packets/sec
5 minute output rate 2729000 bits/sec, 391 packets/sec
5514045 packets input, 1802450404 bytes, 0 no buffer
Received 1712 broadcasts (1109 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
Please help to stop the total broadcast on Gig.
06-18-2010 12:11 AM
Hi Ganesh & Guise,
Implemented the command on L3 switch gig interface (Cisco 4500 series).
interface GigabitEthernet4/36
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 2,4,6
switchport mode trunk
speed 100
duplex full
udld port aggressive
storm-control broadcast level 0.00We have given Level % "0", As per understanding If we configure the 0% level then there should not be any single broadcast on the interface. But even after this we are getting broadcast on the interface.
5 minute input rate 807000 bits/sec, 326 packets/sec
5 minute output rate 2729000 bits/sec, 391 packets/sec
5514045 packets input, 1802450404 bytes, 0 no buffer
Received 1712 broadcasts (1109 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detectedPlease help to stop the total broadcast on Gig.
Hi,
Check out the below link for more information
Hope to Help !!
Ganesh.H
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: