Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

C2960 image support for SNMPv3 and transport output ssh

Hi All.

Which version of image on c2960 switch support snmpV3 and Transport output ssh commands?

Currently we are running c2960-lanbase-mz.122-35.SE5.bin.

Need urgent help...

Regards
Amar

8 REPLIES

Re: C2960 image support for SNMPv3 and transport output ssh

Using the Cisco Feature Navigator, you can download 12.2(53)SE1 with the CAT2960 platform with LAN BASE that supports both SSH and SNMPv3.

http://www.cisco.com/cgi-bin/Software/SWSearch/SWSearch_results.cgi/SWSearch.txt?isChild=false&file_delimiter=contains&search=Search&searchPhrase=c2960-lanbasek9-mz.122-53.SE1.bin

c2960-lanbasek9-mz.122-53.SE1.bin

Community Member

Re: C2960 image support for SNMPv3 and transport output ssh

Hi Neal,

I am Amar colleague, His query is if transport output ssh is supported on any of c2960-48-ttl switch?

Regatrds

Madhu

Community Member

Re: C2960 image support for SNMPv3 and transport output ssh

Hi,

You can used mentioned flash for 2960 and try ("flash:c2960-lanbasek9-mz.122-52.SE.bin")

Thanks

Jyoti

Re: C2960 image support for SNMPv3 and transport output ssh

Hi All.

Which version of image on c2960 switch support snmpV3 and Transport output ssh commands?

Currently we are running c2960-lanbase-mz.122-35.SE5.bin.

Need urgent help...

Regards
Amar

Hi Amar,

Even your current ios supports snmpv3 and ssh

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Community Member

Re: C2960 image support for SNMPv3 and transport output ssh

Hi ganesh

I am Amar Colleague, We tried, Transport output SSH is not supported on c2960-lanbase-mz.122-35.SE5.bin.

Regrads

Amar

Re: C2960 image support for SNMPv3 and transport output ssh

Hi ganesh

I am Amar Colleague, We tried, Transport output SSH is not supported on c2960-lanbase-mz.122-35.SE5.bin.

Regrads

Amar

Amar,

Can you try tansport output all, is it working for ssh or not and snmp v3 should work with this image.

Ganesh.H

Re: C2960 image support for SNMPv3 and transport output ssh

To enable transport out ssh, ensure you are in config mode using "line vty 0 4" and then type "transport input ssh" and "transport output ssh" . To enable snmp on the c2960, you need to be in config mode.

Enabling SNMPv1/v2c on Cisco IOS devices:


To enable SNMPv1/v2c on Cisco IOS devices, follow these steps:
snmp-server community ro
snmp-server community r


Enabling SNMPv3 on Cisco IOS devices:

1. enable

2. configure terminal

3. snmp-server group [groupname {v1 | v2c | v3 [auth | noauth | priv]}] [read readview] [write writeview] [notify notifyview] [access access-list]

4. exit

5. show snmp group

This is for 12.4 but the cli syntax is the same:

http://www.cisco.com/en/US/partner/docs/ios/netmgmt/configuration/guide/nm_cfg_snmp_sup_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1201017

Purple

Re: C2960 image support for SNMPv3 and transport output ssh

  His version may support it but his version is not a crypto code version so it will not work .  Imagename must have a K9 in it.

1367
Views
0
Helpful
8
Replies
CreatePlease to create content