Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Calling all SUP card experts...

Hi everybody,

I'm running diagnostics on various supervisor cards ona 6509 chassis and have found that several of the cards are showing this same problem:

System Bootstrap, Version 7.1(1)

Copyright (c) 1994-2001 by cisco Systems, Inc.

Testing lower main memory - data equals address

Testing lower main memory - checkerboard

Testing lower main memory - inverse checkerboard

Clearing lower 16K memory for cache initialization

Clearing bss

Reading monitor variables from NVRAM

Enabling interrupts

Initializing TLB

Initializing cache

Initializing required TLB entries

Initializing main memory

Sizing NVRAM

Initializing PCMCIA controller

Exiting init

c6k_sup2 processor with 262144 Kbytes of main memory

rommon 1 > boot

loadprog: bad file magic number: 0x0

boot: cannot load "bootflash:"

rommon 2 >

rommon 1 > boot

loadprog: bad file magic number: 0x0

boot: cannot load "bootflash:"

rommon 2 > dir slot0:

Directory of disk0:

2 38282452 -rw- c6k222-psv-mz.122-18.SXD7b.bin

rommon 3 > boot bootflash:c6k222-psv-mz.122-18.SXD7b.bin

open(): Open Error = -9

loadprog: error - on file open

boot: cannot load "bootflash:c6k222-psv-mz.122-18.SXD7b.bin"

I can't believe that all the cards have the same problem so i tried them (at least 4 different ones) in a 6000 series chassis but get the same problem.

I tried loading a different IOS image on the PCMCIA card but no joy.

The only one that i got to load showed the following:

System Bootstrap, Version 5.3(1)

Copyright (c) 1994-1999 by cisco Systems, Inc.

c6k_sup1 processor with 65536 Kbytes of main memory

Autoboot executing command: "boot bootflash:"

loadprog: bad file magic number: 0x0

boot: cannot load "bootflash:"

Exit at the end of BOOT string

rommon 1 > boot

loadprog: bad file magic number: 0x0

boot: cannot load "bootflash:"

rommon 2 > dir bootflash:

File size Checksum File name

13514 bytes (0x34ca) 0x883b31c9 DSDSW01.cfg

13514 bytes (0x34ca) 0x883b31c9 run

13514 bytes (0x34ca) 0x883b31c9 start (deleted)

6304109 bytes (0x60316d) 0x5fd7b46a RTSYNC_RTSYNC_cat6000-sup.5-5-1.bin

13514 bytes (0x34ca) 0x883b31c9 star

13514 bytes (0x34ca) 0x883b31c9 start

rommon 3 > boot bootflash:RTSYNC_RTSYNC_cat6000-sup.5-5-1.bin

Uncompressing file: ####################################################

System Power On Diagnostics

DRAM Size ....................64 MB

Testing DRAM..................Passed

NVRAM Size ...................512 KB

Level2 Cache .................Present

System Power On Diagnostics Complete

Boot image: bootflash:RTSYNC_RTSYNC_cat6000-sup.5-5-1.bin

In Local Test Mode, Synch Failed. Retries: 4

WARNING: Pinnacle has not synchronised

Local Test Mode encounters Minor hardware problem in Module # 1

Is this because i haven't got the latest IOS? Any ideas on why the others aren't operational? Any help would be appreciated.

1 REPLY
Community Member

Re: Calling all SUP card experts...

Is u r router able to boot without any cards installed?

also post the set command output

163
Views
0
Helpful
1
Replies
CreatePlease to create content