Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Can not access management interface on Cisco 4510R

We have a new Cisco 4500R and I have put an IP address and mask on the management interface and even added an default route for the vrf mgmtVrf yet when I plug a PC on the same subnet into the management port or connect it to a switch in the vlan for that subnet I can not ping or telnet to the management port. 

ip vrf mgmtVrf 

!

interface FastEthernet1
ip address 10.11.12.45 255.255.255.0

 ip vrf forwarding mgmtVrf

speed auto

duplex auto 

ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 10.11.12.2

All the default vrf mgmtVrf are configured. Am I missing a step?

Everyone's tags (1)
10 REPLIES

Re: Can not access management interface on Cisco 4510R

U mean even if u put the PC to fa1 we see in the config it is not working?

Sent from Cisco Technical Support iPad App

New Member

Can not access management interface on Cisco 4510R

See response to Jon.

Hall of Fame Super Blue

Can not access management interface on Cisco 4510R

The fa1 one port is up/up ?

Can you post a "sh ip route vrf mgmtVrf"

Jon

New Member

Can not access management interface on Cisco 4510R

Switch#sh ip route vrf mgmtVrf

Routing Table: mgmtVrf

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP

       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

       E1 - OSPF external type 1, E2 - OSPF external type 2

       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

       ia - IS-IS inter area, * - candidate default, U - per-user static route

       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP

       + - replicated route, % - next hop override

Gateway of last resort is 10.11.12.2 to network 0.0.0.0

S*    0.0.0.0/0 [1/0] via 10.11.12.2

      10.0.0.0/8 is variably subnetted, 2 subnets, 2 masks

C        10.11.12.0/24 is directly connected, FastEthernet1

L        10.11.12.45/32 is directly connected, FastEthernet1

Switch#sh int fa1

FastEthernet1 is up, line protocol is up

PC directly connected to fa1 is configured with 10.11.12.2/24 and can not ping fa1 and can't ping PC from switch:

Switch#ping vrf mgmtVrf 10.11.12.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.11.12.2, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)

Hall of Fame Super Blue

Can not access management interface on Cisco 4510R

The PC may have a firewall on it ? which would stop pinging from the switch but not the other way round.

What supervisor and IOS version does the switch have ?

Jon

New Member

Re: Can not access management interface on Cisco 4510R

Switch#sh ver

Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.05.00.E RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2013 by Cisco Systems, Inc.

Compiled Tue 27-Aug-13 17:02 by prod_rel_team

License Information for 'WS-X45-SUP7-E'

    License Level: lanbase   Type: Permanent

    Next reboot license Level: lanbase

No firewalls on the PC and I have tried a couple different PC's along with connecting to a switch.

Hall of Fame Super Blue

Can not access management interface on Cisco 4510R

Can you just confirm, is this a single supervisor setup or do you have two sups in the chassis ?

Jon

New Member

Re: Can not access management interface on Cisco 4510R

Single supervisor set up.

Hall of Fame Super Blue

Can not access management interface on Cisco 4510R

There is nothing wrong with your configuration as far as i can see. I will have a check for bugs but don't hold out too much hope.

Jon

New Member

Was there ever any solution

Was there ever any solution to this? I'm running into the same issue with a new 4500X. Have the exact configuration as the initial post, and it can't ping its gateway. 

899
Views
0
Helpful
10
Replies