Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

can't access after factory reset

I had to do a factory reset on a 881 router and no I can only access via direct console/serial connection. But I'm not sure what to do from here to get it to work.

Output from Hyperterminal:

System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)                                                            

Technical Support: http://www.cisco.com/techsupport                                                  

Copyright (c) 2009 by cisco Systems, Inc.                                        

System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)                                                            

Technical Support: http://www.cisco.com/techsupport                                                  

Copyright (c) 2009 by cisco Systems, Inc.                                        

C880 platform with 262144 Kbytes of main memory                                              

Readonly ROMMON initialized                          

program load complete, entry point: 0x80020000, size: 0x1ee6708                                                              

Self decompressing the image : ##################                                              

################################################################################1: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name                

################################################################################reboot level = advsecurity and License = advsecurity                          

################################################################################C: Crypto engine: onboard 0 State changed                                    

[OK]    

             Restricted Rights Legendtialized              

Dec 10 08:36:

Use, duplication, or disclosure by the Government isState changed                                      

subject to restrictions as set forth in subparagraphd          

Dec 10 08:36:23.079: %LINK-3-UPDOWN: I

(c) of the Commercial Computer Software - Restricted                                                   

Rights clause at FAR sec. 52.227-19 and subparagraph5-UPDOWN: Line protocol on                        

t4, c

           cisco Systems, Inc.            

Dec 10 08:36:25.

           170 West Tasman DrivestEthernet4, changed state to d

           San Jose, California 95134-1706                                  

own

Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, R                                                           

Dec 10 08:36:28.483

ELEASE SOFTWARE (fc1)em restarted --    

Technical Support: http://www.cisco.com/techsupportisco IOS Software, C880 Software (C880DATA-UNIVERSA

Copyright (c) 1986-2012 by Cisco Systems, Inc.                                           

Compiled Wed 21-Mar-12 00:27 by prod_rel_team          

Technical Support: http://www.ci

This product contains cryptographic features and is subje        

                                            

Importers, exporters, distributors and users are responsible for                                                              

compliance with U.S. and local country laws. By using this product you8:36:29.483: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEther

agree to comply with applicable laws and regulations. If you are unable        

t1, changed state to down                        

Dec 10 08

to comply with U.S. and local laws, return this product immediately.ne                                                                 

p

Dec 10 08:36:31.499: %LINEPROTO-5

export@cisco.com.ocol on Interface

Installed image archive                      

Cisco 881 (MPC8300) processor (revision 1.0) with 236544K/25600K bytes of memory        

Dec 10 08:36:34.079: %LINEPROTO-5-UPDOWN: Line protocol on Interface

.s

Processor board ID FGL164227LM                            

5 FastEthernet interfaces

t4, changed state to dow

1 Virtual Private Network (VPN) Module:35.079: %LINK-3-UPDOWN: Interface Fas

256K bytes of non-volatile configuration memory.                                              

125440K bytes of ATA CompactFlash (Read/ termianl                            

Press RETURN to get started!         ^              

%

Jan 2 12:00:02.351: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module nameaging>config                

Translating "config"...domain server (255.255.255.

= c880-data Next reboot level = advsecurity and License = advsecuritydress or host name                           

% Unknown command or c

Dec 10 09:05:07.151: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed                                    

nwbstaging>terminal                  

% I

to: Initialized.              

Dec 10 09:05:07.271: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed

% Invalid input detected at '^' marker.                                    

to: Enabled>setup    

Dec 10 09:05:26.071: %LINK-3-UPDOWN: Interface FastEthernet4, changed state to u                                  

% Bad IP address or h                  

System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)      

own  

Dec 10 09:05:31.599: %SYS-5-CONFIG_I: Configured from memory by console://www.cisco.com/techsupport                                          

Dec 10 09:05:34.419: %SYS-5-RESTART: System restarted --                                

C880 platform with 2

Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.1(4)M4, Rnly ROMMON initialized                          

                            

ELEASE SOFTWAR            

ELEASE SOFTWAR            

t2, changed state to down

Dec 10 09:05:35.419: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEtherne

t3, changed state to down

nwbstaging>cisco

Translating "cisco"...domain server (255.255.255.255)

% Bad IP address or host name

% Unknown command or computer name, or unable to find computer address

nwbstaging>conf

Translating "conf"...domain server (255.255.255.255)

% Bad IP address or host name

% Unknown command or computer name, or unable to find computer address

nwbstaging>config

Translating "config"...domain server (255.255.255.255)

% Bad IP address or host name

% Unknown command or computer name, or unable to find computer address

nwbstaging>setup

Translating "setup"...domain server (255.255.255.255)

% Bad IP address or host name

% Unknown command or computer name, or unable to find computer address

nwbstaging>

Everyone's tags (1)
325
Views
0
Helpful
0
Replies