Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Community Member

Can't see FXS card.

Hi;

I have 2811 router with serial & FXS cards.

I can't find the FXS card??

-----

R1#sh ve

Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS-M), Version 12.4)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Wed 22-Feb-06 16:37 by ccai

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.3(8)T6, R)

R1 uptime is 9 minutes

System returned to ROM by reload at 21:19:18 UTC Thu Apr 12 2007

System image file is "flash:c2800nm-adventerprisek9_ivs-mz.124-4.T2.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.51) with 249856K/12288K bytes of memory.

Processor board ID FTX1032A2CP

2 FastEthernet interfaces

2 Serial(sync/async) interfaces

1 Virtual Private Network (VPN) Module

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

10 REPLIES

Re: Can't see FXS card.

You might need an image that supports voice.

Check Table 3 at :http://www.cisco.com/en/US/products/ps5854/prod_bulletin0900aecd8017a816.html

Community Member

Re: Can't see FXS card.

is the image c2800nm-adventerprisek9_ivs-mz

supported?

Thanks

Waleed.

Re: Can't see FXS card.

Looks like your IOS is IP-BASE. (From your sh ver) "C2800NM-IPBASE-M"

Check with your cisco partner if you got the right software. I *think* it should be "IP

VOICE" when you do a "sh ver". (Assuming you are looking for a IP Voice basic feature to be supported)

Community Member

Re: Can't see FXS card.

Thanks.

but i have lash:c2800nm-adventerprisek9_ivs-mz.124-4.T2.bin image which is voice supported.

Community Member

Re: Can't see FXS card.

I installed Voice image

=======================================

Cisco IOS Software, 2800 Software (C2800NM-IPVOICEK9-M), Version 12.4(12a), RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 22-Feb-07 17:13 by prod_rel_team

ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)

R1 uptime is 31 minutes

System returned to ROM by power-on

System image file is "flash:c2800nm-ipvoicek9-mz.124-12a.bin"

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

Cisco 2811 (revision 53.51) with 251904K/10240K bytes of memory.

Processor board ID FTX1032A2CP

2 FastEthernet interfaces

2 Serial(sync/async) interfaces

DRAM configuration is 64 bits wide with parity enabled.

239K bytes of non-volatile configuration memory.

62720K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

=======================================

Re: Can't see FXS card.

Can you please post all Network modules you have in the router.?

Community Member

Re: Can't see FXS card.

Slot0: WIC2T

Slot3: VIC2FXS

Re: Can't see FXS card.

Here are a couple of things I would try

1) Move the FXS to a different slot and see if it comes up

2) Have the FXS module alone on the router and remove the WIC-2T. Once the router comes up, do a HOT insert of WIC-2T.

Community Member

Re: Can't see FXS card.

Community Member

Re: Can't see FXS card.

2800 series routers take the VIC2-2FXS, it is the version 2.0 of the FXS cards. The VIC-2FXS is for earlier series routers I believe. I use both in my enviroment, you will just need to make sure you get the version 2 FXS card.

239
Views
0
Helpful
10
Replies
CreatePlease to create content