Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
New Member

Can we simulate HSRP configuration using 1x2600 & 1x3560

Hi,

I was just wondering whether we can simulate HSRP failover by using one 2600 router and one 3560 switch where i have 2 FE interfaces at 2600?

I have connected the 2 FE interfaces from 2600 to 3560 switches with 2 routed ports configured respectively and hook up a laptop to 3560 port and did a continuous ping to 2600. However, I did not see the failover when i manually shutdown one interface at the 2600 FE.

Anyways that i can simulate it?

Thanks!!

6 REPLIES
Hall of Fame Super Bronze

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

In order to have HSRP running, both HSRP devices must be on the same LAN.

Can you provide configs along with the show stand output from both devices?

__

Edison.

New Member

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

Thanks!! I will provide the config later on. Meantime, I have tried to configure the 2 FE interface in 2600 with same LAN IP range but failed to do so. ie. FE0/0 IP 192.168.100.2/24, FE0/1 IP 192.168.100.3/24. Hence, I changed the FE0/1 IP to 192.168.110.2/24. The routed ports are configured as follows:

FA0/1: 192.168.100.100 connected to FE0/0

FA0/2: 192.168.110.100 connected to FE0/1

My laptop IP is 10.110.220.150 in VLAN10 on 3560.

My ping is to 192.168.100.1(standby IP) to 2600.

So I think my configurations won't work now since the interfaces are on different segment. Anyway to configure 2600 FE0/0-1 with same segment?

Thanks!!

Gold

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

try configuring one of the ports on your router and a vlan interface on a switch as an hsrp pair.

Hall of Fame Super Bronze

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

HSRP configuration requires you to share this task within (2) physical devices.

You can configure HSRP between the 2600 Router and the 3560 switch.

You already have a Vlan10 on the 3560. I recommend changing the IP on one of the interfaces in the 2600 router to be on that Vlan. Configure the switchport for access-vlan 10, then configure HSRP between Vlan10 Layer3 interface in the switch and the fastethernet in the router connected to that Vlan.

HTH,

__

Edison.

New Member

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

You mean I should configure as follows:

FE0/0 IP 192.168.100.2/24

FE0/1 IP 10.110.220.2/24

Int Fa0/1

Description Connect to FE0/0

no switchport

ip addr 192.168.100.100/24

Int Fa0/2

Description Connect to FE0/1

switchport access vlan 10

switchport mode access

Int Vlan10

ip addr 10.110.220.254/24

Standby 1 IP 10.110.220.1

Standby 1 preempt

My laptop IP is 10.110.220.150 in VLAN10 connected to 3560.

I ping to 192.168.100.1(standby IP) to 2600.

Is it correct?

Hall of Fame Super Bronze

Re: Can we simulate HSRP configuration using 1x2600 & 1x3560

Yes, that should do it.

Once you are done with that configuration, please post the show stand for verification.

__

Edison.

204
Views
0
Helpful
6
Replies
CreatePlease to create content