Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cannot find port

I have a switch running CatOS 7.6(7). It is being monitored via CA's eHealth. EHealth discovered the element: "POOL-enet-port-179", which is reporting bandwidth out utilization, but I cannot see that configured anywhere on the switch. Can anyone please explain what this is? Show ver is below:

sw-25cr1> (enable) sho ver
WS-C6509 Software, Version NmpSW: 7.6(7)
Copyright (c) 1995-2004 by Cisco Systems
NMP S/W compiled on May  6 2004, 23:37:26

System Bootstrap Version: 5.3(1)
System Boot Image File is 'bootflash:cat6000-supk8.7-6-7.bin'
System Configuration register is 0x2

Hardware Version: 2.0  Model: WS-C6509  Serial #: SCA044701LX

PS1  Module: WS-CAC-1300W    Serial #: SON04422265
PS2  Module: WS-CAC-1300W    Serial #: SON04513645

Mod Port Model               Serial #    Versions
--- ---- ------------------- ----------- --------------------------------------
1   2    WS-X6K-SUP1A-2GE    SAD05030GNH Hw : 7.0
                                         Fw : 5.3(1)
                                         Fw1: 5.4(2)
                                         Sw : 7.6(7)
                                         Sw1: 7.6(7)
         WS-F6K-PFC          SAD05030AJN Hw : 1.1  
                                         Sw :
         WS-X6K-SUP1A-2GE    SAD05030GNH Hw : 7.0  
                                         Sw :
3   16   WS-X6416-GE-MT      SAD04190GE3 Hw : 1.1
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
4   48   WS-X6248A-TEL       SAD04450DBM Hw : 2.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
5   48   WS-X6248A-TEL       SAD04290CJT Hw : 3.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
6   48   WS-X6248A-TEL       SAL05062ZK1 Hw : 2.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
7   48   WS-X6248A-TEL       SAD041906BH Hw : 3.0
                                         Fw : 5.4(2)
                                         Sw : 7.6(7)
8   48   WS-X6148-GE-TX      SAD075304E8 Hw : 6.0
                                         Fw : 7.2(1)
                                         Sw : 7.6(7)
9   48   WS-X6148-GE-TX      SAL094760WW Hw : 7.0
                                         Fw : 7.2(1)
                                         Sw : 7.6(7)
15  1    WS-F6K-MSFC2        SAD05030N19 Hw : 1.2
                                         Fw : 12.1(11b)E1
                                         Sw : 12.1(11b)E1

       DRAM                    FLASH                   NVRAM
Module Total   Used    Free    Total   Used    Free    Total Used  Free
------ ------- ------- ------- ------- ------- ------- ----- ----- -----
1       65408K  48172K  17236K  16384K  10924K   5460K  512K  444K   68K

Uptime is 402 days, 3 hours, 16 minutes

Everyone's tags (5)
1 ACCEPTED SOLUTION

Accepted Solutions
Bronze

Re: Cannot find port

Hello,

That port number usually refers to the MIB ifIndex assigned to a certain port. You can try to find port the associated to the PHY 179 with the next command:

show port ifindex

Hope this helps.

2 REPLIES
Bronze

Re: Cannot find port

Hello,

That port number usually refers to the MIB ifIndex assigned to a certain port. You can try to find port the associated to the PHY 179 with the next command:

show port ifindex

Hope this helps.

New Member

Re: Cannot find port

Perfect! Thank you!

366
Views
0
Helpful
2
Replies