Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Attention: The Community will be in read-only mode on 12/14/2017 from 12:00 am pacific to 11:30 am.

During this time you will only be able to see content. Other interactions such as posting, replying to questions, or marking content as helpful will be disabled for few hours.

We apologize for the inconvenience while we perform important updates to the Community.

New Member

Cant access the web camera from outside

hello everyone

im using the ASA 5510 for routing

i just added webcam and cant get it working from outside

i have a static nat from outside to inside

and access list allowing from outside

se attached pictures

Everyone's tags (3)
1 ACCEPTED SOLUTION

Accepted Solutions

Re: Cant access the web camera from outside

Is your ASA's outside interface directly connected out to the Internet and configured with a public IP or is it sitting behind the ISP router with the private IP?  Also what code are you running on that ASA 8.3+ or below?  Like the previous poster mentioned I'm not a fan of GUI so can you paste your configuration from the CLI?  Generally you would do something like this eg;

Camera IP: 192.168.1.10

Public IP: 1.1.1.1

object network obj-192.168.1.10

host 192.168.1.10

exit

object netowrk obj-1.1.1.1

host 1.1.1.1

exit

object service CAMERA_HTTP

service tcp source eq 80

exit

nat (inside, outside) static obj-192.168.1.10 obj-1.1.1.1 service CAMERA_HTTP CAMERA_HTTP

And for the ACL:

access-list outside_acl_in extended permit tcp any gt 1024 host 192.168.1.10 eq 80

Keep in mind if you are forwarding port 80 to something else on that public IP there will be a conflict so you'll need to pick a public IP that free for port 80.

4 REPLIES
Purple

Cant access the web camera from outside

Hi,

I'm not too much fan of the GUI but it seems you should inverse the source and destination interface in your NAT command.

Regards

Alain

Don't forget to rate helpful posts.

Don't forget to rate helpful posts.
New Member

Cant access the web camera from outside

Hi , I did actually it ddnt work  but anywayit has both way nat option checked so in my opinion it should wokr even is it sais Inside- outside

what about my border router (time warner)  i think port 80 needs to be forwarded to somewere

any other ideas ?

Arsen Gharibyan

Network Engineer

http://www.neocomp.com

Re: Cant access the web camera from outside

Is your ASA's outside interface directly connected out to the Internet and configured with a public IP or is it sitting behind the ISP router with the private IP?  Also what code are you running on that ASA 8.3+ or below?  Like the previous poster mentioned I'm not a fan of GUI so can you paste your configuration from the CLI?  Generally you would do something like this eg;

Camera IP: 192.168.1.10

Public IP: 1.1.1.1

object network obj-192.168.1.10

host 192.168.1.10

exit

object netowrk obj-1.1.1.1

host 1.1.1.1

exit

object service CAMERA_HTTP

service tcp source eq 80

exit

nat (inside, outside) static obj-192.168.1.10 obj-1.1.1.1 service CAMERA_HTTP CAMERA_HTTP

And for the ACL:

access-list outside_acl_in extended permit tcp any gt 1024 host 192.168.1.10 eq 80

Keep in mind if you are forwarding port 80 to something else on that public IP there will be a conflict so you'll need to pick a public IP that free for port 80.

New Member

Cant access the web camera from outside

Thank you for your reply the issue was in static route on ASA

asa cant get to the appropriate vlan

192.168.10.0 255.255.255.255

changed to 192.168.10.0 255.255.255.0

and it worked

601
Views
0
Helpful
4
Replies
CreatePlease to create content