Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Cat 6500 - WS-X6548-GE-TX module not active

Hi,

I have problem with one of my Cat 6500 module that cannot work.

The module is WS-X6548-GE-TX and currently using "c6sup22-psv-mz.121-13.E9.bin".

I check cisco website and it's recommended use "12.2(17d)SXB" IOS version. But when I check, this version has been deferred.

Does anyone help me, what IOS version that can make my WS-X6548-GE-TX work properly ?

Additional information :

I'm using Supervisor Engine 2 (WS-X6K-SUP2-2GE)

thanks

4 REPLIES
Hall of Fame Super Blue

Re: Cat 6500 - WS-X6548-GE-TX module not active

Could you post output of a "sh module"

New Member

Re: Cat 6500 - WS-X6548-GE-TX module not active

Here is the output :

CORE#sh module

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SALXXXXXXXX

2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-SUP2-2GE SALXXXXXXXX

3 24 SFM-capable 24-port 100FX Multi mode WS-X6524-100FX-MM SALXXXXXXXX

4 48 48-port 10/100 mb RJ45 WS-X6148-RJ-45 SALXXXXXXXX

5 8 8 port 1000mb GBIC Enhanced QoS WS-X6408A-GBIC SALXXXXXXXX

6 48 unknown FRU type (major = 0x6003, mino WS-X6548-GE-TX SALXXXXXXXX

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0006.d65d.41xx to 0006.d65d.41xx 4.3 6.1(3) 7.5(0.6)HUB1 Ok

2 0006.d65d.44xx to 0006.d65d.44xx 4.3 6.1(3) 7.5(0.6)HUB1 Ok

3 000d.659b.dexx to 000d.659b.dexx 1.6 6.3(1) 7.5(0.6)HUB1 Ok

4 000d.bd0d.d6xx to 000d.bd0d.d6xx 1.3 5.4(2) 7.5(0.6)HUB1 Ok

5 0013.7f0e.0fxx to 0013.7f0e.0fxx 3.1 5.4(2) 7.5(0.6)HUB1 Ok

6 001d.a25f.3exx to 001d.a25f.3fxx 11.3 Unknown Unknown PwrDown

Mod Sub-Module Model Serial Hw Status

--- --------------------------- --------------- --------------- ------- -------

1 Policy Feature Card 2 WS-F6K-PFC2 SALXXXXXXXX 3.4 Ok

1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SALXXXXXXXX 2.5 Ok

2 Policy Feature Card 2 WS-F6K-PFC2 SALXXXXXXXX 3.4 Ok

2 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SALXXXXXXXX 2.5 Ok

Mod Online Diag Status

--- -------------------

1 Pass

2 Pass

3 Pass

4 Pass

5 Pass

6 Unknown

Hall of Fame Super Blue

Re: Cat 6500 - WS-X6548-GE-TX module not active

Arianto

If you are running in native mode then you need a minimum of 12.1(19), see this link -

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.1E/native/release/notes/OL_2310.html#wp1344016

If you are in hybrid mode then you need CatOS minimum of 7.6(1) on the supervisor engine.

If you are in native there is nothing to stop you upgrading to a 12.2SXF version which will support your card although you need to check the memory requirements, see this link -

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/ios/12.2SXF/native/release/notes/OL_4164.html#wp2561255

Jon

New Member

Re: Cat 6500 - WS-X6548-GE-TX module not active

Hi Jon,

thanks for your help.

i will try for this.

349
Views
4
Helpful
4
Replies