Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

cat4000-i9s-mz.121-19.EW1.bin

hello!

i have read a reply FROM Ankur that the switchover in the RPR Mode between 3 to 4 Mts & 30 to 60 Seconds in RPR +.but on my 4507R(2 Sup WS-X4515)i saw just RPR,.CAN I Upgrade my IOS To support RPR+?30 Sec its goof for Switch over

My Current IOS:cat4000-i9s-mz.121-19.EW1.bin

11 REPLIES
New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

why not consider SSO?

Silver

Re: cat4000-i9s-mz.121-19.EW1.bin

You can upgrade to 12.2(25)EWA to have SSO and get <30s switchovers or 12.2(31)SGA code to support SSO with NSF, to have possible >5s switchovers. Here is the link for 12.2SGA SSO with NSF:

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31a/config/nsfwsso.htm

Cisco Employee

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi Ali,

I would suggest to use SSO with NFS between the supervisor engines. SSO/NSF give you sub-milisecond fail-over between the sup's for both L2/L3 failover though we claim it around 0-3 seconds which depends on the traffic flow. My self has tested same with 900Mbps traffic and the failover time was arnd 300 milisecond.

You need atleaset 12.2.31SG for the same.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31s/conf/nsfwsso.htm

HTH,

-amit singh

New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi Amit!

plz give the full name of the IOS

10XS

New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi!

do i need to update the IOS ON BOTH Supervisor or Just on 1 of them

10xs

New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

ANY REPLY HERE

Cisco Employee

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi Ali,

This is the full image name that you need on the box :

cat4500-ipbase-mz

HTH,

-amit singh

Cisco Employee

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi Ali,

Have a look at this release notes for supported IOS 12.2(31)SG

http://www.cisco.com/en/US/products/hw/switches/ps4324/prod_release_note09186a0080758ff3.html#wp686916

HTH

Ankur

New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

Hello Ankur;Hello Amit!

do i need to copy this IOS cat4500-ipbase-mz

TO Both bootflash on the 2 sup.or just on 1 bootflash???

plz send me the Link to to this

10xs

Cisco Employee

Re: cat4000-i9s-mz.121-19.EW1.bin

Hi Ali,

You have to copy the image on both bootflash.

This link will help you doing upgrade on both the supervisors.

http://www.cisco.com/en/US/products/hw/switches/ps4324/products_configuration_guide_chapter09186a008036715c.html#wp1104060

HTH

Ankur

New Member

Re: cat4000-i9s-mz.121-19.EW1.bin

Ankur My Freind

10xs

478
Views
25
Helpful
11
Replies
CreatePlease login to create content