Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. If you'd prefer to explore, try our test area to get started. And see here for current known issues.

New Member

Catalyst 4500 Supervisor 6L SFP Utilization

Hi,

I need to design a solution with a catalyst 4507R-E chassi with redundant supervisors (WS-X45-SUP6L-E), and i need 6 SFP's to interconect to 5 remote floors. It's possible use both supervisors slots, or i can't use the redundant supervisors slots ? With this option it's possible to use the two 10GE slots from both supervisors with SFP adaptors and put the 6 SFP's on it ?

Thanks !!!

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Silver

Re: Catalyst 4500 Supervisor 6L SFP Utilization

Hello Carlos,

yes it is possible to use the SFP ports on the standby supervisor

see

switch>sh cdp n | exclude SEP

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,

D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID Local Intrfce Holdtme Capability Platform Port ID

router1

Ten 3/1 127 R S I WS-C6509- Ten 4/2

router2

Ten 4/1 130 R S I WS-C6509- Ten 4/2

switch>sh module

Chassis Type : WS-C4507R-E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 48 10/100BaseTX (RJ45)V WS-X4148-RJ45V JAE0621003W

3 6 Sup II+10GE 10GE (X2), 1000BaseX (SFP) WS-X4013+10GE JAE1237ULNB

4 6 Sup II+10GE 10GE (X2), 1000BaseX (SFP) WS-X4013+10GE JAE1237ULNZ

5 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE1221IZPR

6 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE1238UXKZ

This is an handy feature and works well on previous supervisor models I would expect to work also on the sup 6 L -E

Hope to help

Giuseppe

2 REPLIES
Hall of Fame Super Silver

Re: Catalyst 4500 Supervisor 6L SFP Utilization

Hello Carlos,

yes it is possible to use the SFP ports on the standby supervisor

see

switch>sh cdp n | exclude SEP

Capability Codes: R - Router, T - Trans Bridge, B - Source Route Bridge

S - Switch, H - Host, I - IGMP, r - Repeater, P - Phone,

D - Remote, C - CVTA, M - Two-port Mac Relay

Device ID Local Intrfce Holdtme Capability Platform Port ID

router1

Ten 3/1 127 R S I WS-C6509- Ten 4/2

router2

Ten 4/1 130 R S I WS-C6509- Ten 4/2

switch>sh module

Chassis Type : WS-C4507R-E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 48 10/100BaseTX (RJ45)V WS-X4148-RJ45V JAE0621003W

3 6 Sup II+10GE 10GE (X2), 1000BaseX (SFP) WS-X4013+10GE JAE1237ULNB

4 6 Sup II+10GE 10GE (X2), 1000BaseX (SFP) WS-X4013+10GE JAE1237ULNZ

5 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE1221IZPR

6 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE1238UXKZ

This is an handy feature and works well on previous supervisor models I would expect to work also on the sup 6 L -E

Hope to help

Giuseppe

New Member

Re: Catalyst 4500 Supervisor 6L SFP Utilization

in all ports ?

205
Views
0
Helpful
2
Replies