Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

New Member

Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Hi All,

We have Sup 2/MSFC 2 running on the Catalyst and this wont detect the line cards. Please find the show commands below:

console> sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

4 4 Unknown Card power-bad

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAL0735KN7W

15 SAL0720D8VX

4

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-06-d6-5d-61-ce to 00-06-d6-5d-61-cf 4.3 7.1(1) 7.6(7)

00-06-d6-5d-61-cc to 00-06-d6-5d-61-cd

00-1d-a1-e6-a3-c0 to 00-1d-a1-e6-a7-bf

15 00-09-12-56-db-40 to 00-09-12-56-db-7f 2.5 12.1(13)E1 12.1(13)E11

4 unknown

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw

--- ----------------------- ------------------- ----------- ------ ------

1 L3 Switching Engine II WS-F6K-PFC2 SAL0735KNFZ 3.4

Console>

Console> Sh ver

Console> sh ver

WS-C6506-E Software, Version NmpSW: 7.6(7)

Copyright (c) 1995-2004 by Cisco Systems

NMP S/W compiled on May 6 2004, 23:21:07

System Bootstrap Version: 7.1(1)

System Boot Image File is 'bootflash:cat6000-sup2k8.7-6-7.bin'

System Configuration register is 0x2102

Hardware Version: 1.1 Model: WS-C6506-E Serial #: SAL114031RE

PS2 Module: WS-CAC-3000W Serial #: SNI1147AWBN

Mod Port Model Serial # Versions

--- ---- ------------------- ----------- --------------------------------------

1 2 WS-X6K-SUP2-2GE SAL0735KN7W Hw : 4.3

Fw : 7.1(1)

Fw1: 6.1(3)

Sw : 7.6(7)

Sw1: 7.6(7)

WS-F6K-PFC2 SAL0735KNFZ Hw : 3.4

Sw :

WS-X6K-SUP2-2GE SAL0735KN7W Hw : 4.3

Sw :

15 1 WS-F6K-MSFC2 SAL0720D8VX Hw : 2.5

Fw : 12.1(13)E11

Sw : 12.1(13)E11

DRAM FLASH NVRAM

Module Total Used Free Total Used Free Total Used Free

------ ------- ------- ------- ------- ------- ------- ----- ----- -----

1 524288K 69795K 192349K 32768K 15098K 17670K 512K 256K 256K

Uptime is 0 day, 0 hour, 4 minutes

Console>

Thanks & Regards

Subra

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Subra

Firstly you don't have an SFM (switch Fabric Module) so all your linecards will share the 32Gbps classic bus.

Secondly the WS-X6148A-GE-TX is positioned as a wiring closet module ie. you probably wouldn't want to be using this module for a server farm. It really depends on what you want to use the switch for.

Not sure what you mean about negative performance. As i say you are limited by the available switch fabric.

What are you intending to use the module for and are you intending to install any other modules and what would these be used for ?

Jon

10 REPLIES
Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Subra

You need a minimum of CatOS 8.4(1) to support this card. Please see attached release notes for details

http://www.cisco.com/en/US/docs/switches/lan/catalyst6500/catos/8.x/release/notes/OL_4498.html

Jon

New Member

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Hi Jon,

Thanks for the Input but I am curious about the jumbo Frames support. All we are cocerned about is a regular 1518 byte frame support. What difference will it actually make.

Thanks & Regards

Subra

Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Subra

You've confused me now. What do you mean about jumbo frames support and how is this related to the card not being recognised ?

Jon

New Member

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

hi jon,

Sorry. May be i am not asking you the right question.

Lets say i upgrade the catos on the switch to support the line card.

The Line card - WS - X6148 A - GE - TX has got the Jumbo frame support but all we will do is a regular frame on this switch.

Will it make any difference using this line card in the switch.

THANKS & REGARDS

SUBRA

Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

If you don't need the jumbo support then it comes down to the question of what other alternative modules you can use.

Do you want PoE and do you want 10/100/1000 interface capability.

Jon

New Member

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Hi Jon,

We dont need POE as well. But we are planning to use the same line card in that case do i have any negative impact on the performance or is it any good.

thanks and regards

subra

Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Subra

Firstly you don't have an SFM (switch Fabric Module) so all your linecards will share the 32Gbps classic bus.

Secondly the WS-X6148A-GE-TX is positioned as a wiring closet module ie. you probably wouldn't want to be using this module for a server farm. It really depends on what you want to use the switch for.

Not sure what you mean about negative performance. As i say you are limited by the available switch fabric.

What are you intending to use the module for and are you intending to install any other modules and what would these be used for ?

Jon

New Member

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Hi,

Thanks for the Input. We are planning to put 2 of the line cards and create vlans for a server farm. No other modules will be installed except for these.

Thanks & regards

Subra

Hall of Fame Super Blue

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Subra

These modules are classic modules so they only connect to the 32Gbps shared bus. So you have 2 x WS-X6148A-GE-TX modules both connecting to the shared 32Gbps bus. So you need to factor this into the equation. For example if you were to fully populate these modules with server you would be very heavily oversubscribed.

It all depends on how many servers you intend to connect and what throughput you need for each server.

It is worth saying again that these modules are not really designed for server farms. If you connect to these servers over a WAN then the WAN speed might be the limiting factor but within a campus environment it may very well not work as you hoped.

Jon

New Member

Re: Catalyst - 6506E - Wont detect WS-X6148A-GE-TX

Hi Jon,

Thanks again. We will have only a Handful of Servers connecting and hence it shouldnt be problem.

Thanks & Regards

Subra

358
Views
0
Helpful
10
Replies