Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements
Highlighted

Cisco 1720 FE Default Duplex Setting

hi experts,

i've got a cisco 1720 router. would like to know what is the default duplex setting for FE port?

cisco 1720 (MPC860) processor (revision 0x501) with 12288K/4096K bytes of memory.
Processor board ID JAD041306KV (1507224326), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
4096K bytes of processor board System flash (Read/Write)

----------

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed auto
no cdp enable
end

1 ACCEPTED SOLUTION

Accepted Solutions
Hall of Fame Super Blue

Re: Cisco 1720 FE Default Duplex Setting

How about "no full-duplex"?  Make sure you set your speed to auto.

8 REPLIES

Re: Cisco 1720 FE Default Duplex Setting

Hi,

The default duplex setting is to auto-negotiate.

You can check doing a ''sh int fas 0'' instead than ''sh run int fas0''

Federico.

Re: Cisco 1720 FE Default Duplex Setting

thanks federico! i've configured this port for full-duplex and now want to revert back to auto-negotiate (default). could you assist how to revert back?

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed 100
full-duplex  -->
no cdp enable
end

Hall of Fame Super Blue

Re: Cisco 1720 FE Default Duplex Setting

Try "speed auto" and then "duplex auto".  I believe this IOS is one of those "if it's default, it won't appear" concept.

Re: Cisco 1720 FE Default Duplex Setting

thanks federico! i've configured this port for full-duplex and now want to revert back to auto-negotiate (default). could you assist how to revert back?

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed 100
full-duplex  -->
no cdp enable
end

Hi,

Configure with below mentioned steps for auto configuration

Step 1 Router# configure terminal
Step 2 Router(Config)# interface ethernet 0/11
Step 3 Router(Config-if)# speed auto
Step 4 Router(Config-if)# duplex auto

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Re: Cisco 1720 FE Default Duplex Setting

hi ganesh,

thanks for your inputs! however, this router doesn't support the command you've mentioned. is there a workaround to set the interface to "duplex auto"?

1720(config)#int f0
1720(config-if)#dup?
% Unrecognized command

1720(config-if)#full-duplex ?
 
       
1720(config-if)#half-duplex ?

Hall of Fame Super Blue

Re: Cisco 1720 FE Default Duplex Setting

How about "no full-duplex"?  Make sure you set your speed to auto.

Re: Cisco 1720 FE Default Duplex Setting

awesome! it worked! thank you!

1720(config-if)#no full-duplex ?
 

Hall of Fame Super Blue

Re: Cisco 1720 FE Default Duplex Setting

Thanks for the rating.

866
Views
5
Helpful
8
Replies
CreatePlease to create content