Cisco Support Community
cancel
Showing results for 
Search instead for 
Did you mean: 
Announcements

Welcome to Cisco Support Community. We would love to have your feedback.

For an introduction to the new site, click here. And see here for current known issues.

Cisco 1720 FE Default Duplex Setting

hi experts,

i've got a cisco 1720 router. would like to know what is the default duplex setting for FE port?

cisco 1720 (MPC860) processor (revision 0x501) with 12288K/4096K bytes of memory.
Processor board ID JAD041306KV (1507224326), with hardware revision 0000
M860 processor: part number 0, mask 32
Bridging software.
X.25 software, Version 3.0.0.
1 FastEthernet/IEEE 802.3 interface(s)
1 Serial(sync/async) network interface(s)
32K bytes of non-volatile configuration memory.
4096K bytes of processor board System flash (Read/Write)

----------

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed auto
no cdp enable
end

1 ACCEPTED SOLUTION

Accepted Solutions
Highlighted
Hall of Fame Super Gold

Re: Cisco 1720 FE Default Duplex Setting

How about "no full-duplex"?  Make sure you set your speed to auto.

8 REPLIES

Re: Cisco 1720 FE Default Duplex Setting

Hi,

The default duplex setting is to auto-negotiate.

You can check doing a ''sh int fas 0'' instead than ''sh run int fas0''

Federico.

Re: Cisco 1720 FE Default Duplex Setting

thanks federico! i've configured this port for full-duplex and now want to revert back to auto-negotiate (default). could you assist how to revert back?

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed 100
full-duplex  -->
no cdp enable
end

Hall of Fame Super Gold

Re: Cisco 1720 FE Default Duplex Setting

Try "speed auto" and then "duplex auto".  I believe this IOS is one of those "if it's default, it won't appear" concept.

Re: Cisco 1720 FE Default Duplex Setting

thanks federico! i've configured this port for full-duplex and now want to revert back to auto-negotiate (default). could you assist how to revert back?

1720#sh run int f0
Building configuration...

Current configuration:
!
interface FastEthernet0
description Customer Network
ip address X.X.X.X 255.255.255.224
no ip route-cache
no keepalive
speed 100
full-duplex  -->
no cdp enable
end

Hi,

Configure with below mentioned steps for auto configuration

Step 1 Router# configure terminal
Step 2 Router(Config)# interface ethernet 0/11
Step 3 Router(Config-if)# speed auto
Step 4 Router(Config-if)# duplex auto

Hope to Help !!

Ganesh.H

Remember to rate the helpful post

Re: Cisco 1720 FE Default Duplex Setting

hi ganesh,

thanks for your inputs! however, this router doesn't support the command you've mentioned. is there a workaround to set the interface to "duplex auto"?

1720(config)#int f0
1720(config-if)#dup?
% Unrecognized command

1720(config-if)#full-duplex ?
 
       
1720(config-if)#half-duplex ?

Highlighted
Hall of Fame Super Gold

Re: Cisco 1720 FE Default Duplex Setting

How about "no full-duplex"?  Make sure you set your speed to auto.

Re: Cisco 1720 FE Default Duplex Setting

awesome! it worked! thank you!

1720(config-if)#no full-duplex ?
 

Hall of Fame Super Gold

Re: Cisco 1720 FE Default Duplex Setting

Thanks for the rating.

845
Views
5
Helpful
8
Replies
CreatePlease login to create content