09-03-2010 12:55 AM - edited 03-06-2019 12:48 PM
Hi to everybody,
I am trying to configure a 2613 XM as terminal server for my first time.
Follow the configuration:
aaa new-model
!
!
aaa session-id common
ip subnet-zero
ip cef
!
!
!
no ip domain lookup
ip host ASA-MNG_p 2002 192.168.1.1
ip host ASA-PUB_p 2003 192.168.1.1
ip host CORE1 2000 192.168.1.1
no ftp-server write-enable
!
!
!
!
interface Loopback0
ip address 192.168.1.1 255.255.255.255
!
interface FastEthernet0/0
ip address 192.168.2.66 255.255.255.252
duplex auto
speed auto
!
ip default-gateway 192.168.2.65
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.2.65
no ip http server
!
I have attached the first ports 0-7 of the Async module from the 2613 to a 6500 console port using a Async BreakOut cable, than i tryed to do the connect command in this way:
connect CORE1 2000
% Connection refused by remote host
Why I got a refused connection?
Thanks in advance & Best Regards.
Igor.
Solved! Go to Solution.
09-03-2010 06:13 AM
Hello,
Your terminal lines are from 2033 to 2048. Please try the following:
no ip host ASA-MNG_p 2002 192.168.1.1
no ip host ASA-PUB_p 2003 192.168.1.1
no ip host CORE1 2000 192.168.1.1
ip host ASA-MNG_p 2034 192.168.1.1
ip host ASA-PUB_p 2035 192.168.1.1
ip host CORE1 2033 192.168.1.1
and then try to connect using
connect CORE1 2033
Hope this helps.
Regards,
NT
09-03-2010 06:00 AM
Hello,
Can you please post the output of "show run | be line" command?
Regards,
NT
09-03-2010 06:07 AM
Follow:
line con 0
transport preferred none
line 33 48
session-timeout 60
no flush-at-activation
absolute-timeout 60
transport preferred telnet
transport input all
stopbits 1
flowcontrol hardware
line aux 0
transport preferred none
speed 38400
line vty 0 3
line vty 4
transport preferred none
!
09-03-2010 06:13 AM
Hello,
Your terminal lines are from 2033 to 2048. Please try the following:
no ip host ASA-MNG_p 2002 192.168.1.1
no ip host ASA-PUB_p 2003 192.168.1.1
no ip host CORE1 2000 192.168.1.1
ip host ASA-MNG_p 2034 192.168.1.1
ip host ASA-PUB_p 2035 192.168.1.1
ip host CORE1 2033 192.168.1.1
and then try to connect using
connect CORE1 2033
Hope this helps.
Regards,
NT
09-03-2010 07:04 AM
Many Thanks for your help.
I have only one little problem with the escape sequence, that shold be Ctrl-^, X
but do not works, I think it depends from my putty emuletor settings.
WBR,
Igor.
12-09-2010 08:04 AM
Hi.. i have a issue after follow what u have recommended but still stuck at there.. do i need to configure any thing at the console port of the router that attach to the async port? hope that u can help me
CBJ-OOB#connect 10.1.1.1 2033
Trying 10.1.1.1, 2033 ... Open
CBJ-OOB#connect 10.1.1.1 2033
Trying 10.1.1.1, 2033 ... Open
CBJ-OOB#sh line
Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int
0 CTY - - - - - 0 0 0/0 -
* 33 TTY 9600/9600 - - - - - 3 0 0/0 -
34 TTY 9600/9600 - - - - - 0 0 0/0 -
35 TTY 9600/9600 - - - - - 0 0 0/0 -
36 TTY 9600/9600 - - - - - 0 0 0/0 -
37 TTY 9600/9600 - - - - - 0 0 0/0 -
38 TTY 9600/9600 - - - - - 0 0 0/0 -
39 TTY 9600/9600 - - - - - 0 0 0/0 -
40 TTY 9600/9600 - - - - - 0 0 0/0 -
41 TTY 9600/9600 - - - - - 0 0 0/0 -
42 TTY 9600/9600 - - - - - 0 0 0/0 -
43 TTY 9600/9600 - - - - - 0 0 0/0 -
44 TTY 9600/9600 - - - - - 0 0 0/0 -
45 TTY 9600/9600 - - - - - 0 0 0/0 -
46 TTY 9600/9600 - - - - - 0 0 0/0 -
47 TTY 9600/9600 - - - - - 0 0 0/0 -
48 TTY 9600/9600 - - - - - 0 0 0/0 -
65 AUX 9600/9600 - - - - - 0 0 0/0 -
* 66 VTY - - - - 10 4 0 0/0 -
67 VTY - - - - 10 0 0 0/0 -
68 VTY - - - - 10 0 0 0/0 -
69 VTY - - - - 10 0 0 0/0 -
70 VTY - - - - 10 0 0 0/0 -
Line(s) not in async mode -or- with no hardware support:
1-32, 49-64
line con 0
line 33
session-timeout 60
exec-timeout 0 0
no flush-at-activation
absolute-timeout 60
transport preferred none
transport input all
transport output all
escape-character BREAK
stopbits 1
flowcontrol hardware
line 34 40
session-timeout 60
exec-timeout 0 0
no flush-at-activation
absolute-timeout 60
transport preferred telnet
transport input all
escape-character BREAK
stopbits 1
flowcontrol hardware
line 41 48
session-timeout 60
exec-timeout 0 0
no flush-at-activation
absolute-timeout 60
transport preferred telnet
transport input all
stopbits 1
flowcontrol hardware
line aux 0
line vty 0 4
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide